LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 66

LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 27

23

Battle Ax Skid Loader OM

Maintenance

Belt Tension Adjustment

DANGER:

Shut down and lock out power

from the loader before adjusting the drive
belt. Failure to do so could result in serious
injury or death.

Remove belt cover and motor cover. Refer to “Removing
Belt Cover” on page 21 and “Removing Motor Cover”
on page 22 for instructions.

1

1

2

Loosen the four mounting bolts (1). Then loosen the
overhung load adapter support bracket bolts (2).

4

3

1/2 in.

3/8 in.

Loosen the jam nut (3). Then turn the hex bolt (4) to either
increase or decrease belt tension.

Belt should move no more than 3/8 in. (9.5 mm) to the
left, and no more than 1/2 in. (12.7 mm) to the right when
pressure applied at the midpoint.

Retighten the jam nut (3).

Retighten overhung load adapter support bolts (1) and
the mounting bolts (2).

Replacing Belt

To replace the belt, follow the procedures for "Belt
Tension Adjustment" preceding this subsection and
decrease the belt tension additionally to allow the belt to
slide over the top sprocket.

NOTE:

When replacing or installing a new belt, align
the grooves in the belt with the upper and lower
pulleys.

Install the belt and adjust the tension accordingly. Refer
again to the "Belt Tension Adjustment" procedure and
follow the instructions completely.

Sprocket Removal

The steps to remove either the upper or lower sprocket
are identical. For this procedure the upper sprocket is
discussed. Follow the same procedure to remove the
lower sprocket.

NOTE:

See page 40 for a master drawing of all belt/
sprocket combinations. The page provides a
reference to an exploded view with a complete
parts list for each combination.

1. Disconnect or turn off all power to the Battle Ax.

DANGER:

Shut down and lock out power

from the loader before removing sprockets.
Failure to do so could result in serious injury or
death.

Remove the drive belt by following the instructions
in "Belt Tension Adjustment" and “Replacing Belt”
preceding this subsection.

(Procedure continued on following page.)

«
...
25
26
27
28
29
...
»

Содержание Battle Ax 207460



































































Отзывы:

Нет отзывов