LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 66

LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 16

12

Battle Ax Skid Loader OM

Fully raise the attachment-locking levers on the loader
mounting plate.

1

Tilt the loader mounting plate ahead. Drive forward with
the loader and hook the top edge of the loader mounting
plate under the top flange (1) on the Battle Ax mounting
plate. Be careful not to damage the locking levers on the
loader mounting plate.

Tilt the loader mounting plate back until the Battle Ax
mounting plate is firmly against the loader mounting
plate, but Do Not lift the attachment off the ground.

WARNING:

Before you leave the operator’s

seat: Lower the lift arms, put the attachment
on the ground. Stop engine and remove
ignition key. Engage the parking brake.

Fully lower the attachment-locking levers on the loader
mounting plate.

WARNING:

Locking-wedge pins must extend

through the holes in attachment-mounting
plate. Levers must be fully down in the locked
over-center position. Failure to secure wedge
pins can allow attachment to come off,
causing serious injury or death.

Install the two safety bolts through the loader mounting
plate and into the Battle Ax Light mounting plate. Tighten
the two safety bolts to the proper torque, see “Torque
Specifications” on page 59.

Pusher Bar Assembly (Cont’d)

Reinstall the hardware in the correct order and hand-
tighten.

Move the opposite arm into place so the upper hole
aligns with the corresponding hole position as the
opposite side. Reinstall the hardware in the correct order.

Tighten all hardware on both sides.

The strap/chain from the hoist can now be removed.

Removing Shipping Stands

1

2

2

1

Unfasten the bolt, washer, and nut sets (1) (two sets on
each side) and remove the shipping stands (2).

NOTE:

Do not discard the shipping stands. They are
used to stabilize the Battle Ax during storage.
Keep in a secure location until ready to store.

Installing the Battle Ax to the Loader

1

1

Remove the two safety bolts (1).

Set-up Instructions

«
...
14
15
16
17
18
...
»

Содержание Battle Ax 207460



































































Отзывы:

Нет отзывов