LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 66

LOFTNESS Battle Ax 207460 Скачать руководство пользователя страница 30

26

Battle Ax Skid Loader OM

Recutter Removal/Replacement

DANGER:

Shut down power from the loader

before removing and replacing the recutter.
Failure to do so could result in serious injury
or death.

2

A

4

3 2

1

NOTE:

Mounting hardware for the recutter is shown
at the locations above (A). There are seven
hardware locations for the 61" Battle Ax, and
eight locations for the 71" Battle Ax.

To remove the recutter (1), unfasten all hardware shown
at locations “A” - the 1/2" nuts (2), 1/2" washers (3), and
the 4" bolts (4). Support the recutter before removing the
last two bolts.

Over time, the recutter edge will become worn and
rounded from use. There are a total of 4 wear edges
available by removing and flipping the bar, side to side
and front to back.

CAUTION:

If adjusting the recutter after the

machine has been used, the recutter should
be completely removed to clear any debris
away from contact surfaces before assembly
and tightening. FAILURE TO DO SO COULD
RESULT IN SEVERE DAMAGE TO THE
MACHINE!

To install the clean or new recutter, align the holes in the
recutter with the holes on the frame. Re-install the bolts,
then add the washers and nuts. Torque to 83 ft.-lbs.

Installing/Removing the Hood Liner

DANGER:

Shut down power from the loader

before installing or removing the hood liner.
Failure to do so could result in serious injury
or death.

Clearing the Cutter Bar

For a new or unused machine:

1

2

Loosen (do not remove) the hardware (1) securing the
cutter bar (2) (seven securing locations).

This will provide enough room to mount the hood liner
without removing the cutter bar.

For a machine that has already been used or put

into service:

IMPORTANT

:

Over time, a Battle Ax put into service
will collect dirt, debris, and other matter
on and around the cutter bar and the
recutter. For this reason it is important
that both are completely removed and all
contact surfaces cleaned before it can be
returned to the machine.

To remove the cutter bar, see “Cutter Bar Adjustment/
Removal” on page 15 for complete and thorough
instructions. To remove the recutter, see "Recutter
Removal/Replacement" on this page. Obey all cautions
and warnings described in each procedure.

CAUTION:

The cutter bar must be completely

removed to clear any debris away from contact
surfaces before assembly and tightening.
FAILURE TO DO SO COULD RESULT IN
SEVERE DAMAGE TO THE MACHINE!

(Procedure continued on following page.)

Maintenance

«
...
28
29
30
31
32
...
»

Содержание Battle Ax 207460



































































Отзывы:

Нет отзывов