LOFTNESS 15 Скачать руководство пользователя страница 41

Страница: 41 / 106

Windrow Crop Shredder OM

Working to Transport Configuration

Procedure (Cont'd)

Folding the Operation Hitch (Cont'd)

With pins removed, lower the hitch with the hand winch
until the braces (3 & 4) drop clear through the hitch.

Using the hand winch, raise the hitch up to the storage
position. Use a brace pin (5) and linchpin (6) to secure
into position.

Transporting

Obey these safety instructions before transporting the
windrow shredder on public roads.

CAUTION:

Do not exceed 20 mph when

transporting the shredder.

CAUTION:

Verify warning lights are properly

operating before transporting the shredder
on public roads. Make sure “Slow Moving
Vehicle” decal is visible.

CAUTION:

Verify all jacks have been returned

to their storage positions and the jack stands
are raised and locked in their highest position
before transport.

DANGER:

Verify the

operation hitch

secure and cannot drop during transport.
Failure to secure could result in serious injury,
or death, to other drivers on the road.

DANGER:

Make sure fingers on deflector

are lowered. Refer to “Deflector Angle
Adjustment” on page 23 for instructions.

Operating Instructions

Содержание 15











































































































Результаты поиска

Содержание 15

Отзывы:

Похожие инструкции для 15

Бренды по названию

Популярные бренды

LOFTNESS 15, Руководство пользователя и каталог запасных частей

Результаты поиска

Содержание 15

Отзывы:

Похожие инструкции для 15

Бренды по названию

Популярные бренды