LOFTNESS 15 Скачать руководство пользователя страница 25

Страница: 25 / 106

Windrow Crop Shredder OM

Equipment Set-up (Cont'd)

Attach bottom corner of wing door to body with 5/8" x
1-1/2" hex bolt (9), 1/2" flat washer and 1/2" lock nut.

IMPORTANT:

Do not tighten the hardware completely.

Repeat procedure on opposite side.

Attach the bottom mid-sections of the wing doors
together with 5/8" x 1-1/2" hex bolt (10), 1/2" flat washer
and 1/2" lock nut. (Left side shown.)

IMPORTANT:

Do not tighten the hardware completely.

Repeat procedure on opposite side.

Tightening Hardware

IMPORTANT:

When assembly is complete, tighten all

the hardware in the set-up procedure.
Follow the instructions below as a guide.

With all the sections and hardware assembled, level the
tail and tighten the 3/4" bolts holding the tail arms to the
body arms.

Next tighten the hardware connecting the wing tops to
the body and the tail section.

Repeat procedure on opposite side.

Push the wings doors underneath to minimize the gap at
the top and tighten the 5/8" bolts.

Repeat procedure for all four wing door sections.

Tighten the hardware at the bottom of the wing doors.

Remove green lifting rings, 5/8" hardware, and lifting
chains.

Set-up Instructions

Содержание 15











































































































Результаты поиска

Содержание 15

Отзывы:

Похожие инструкции для 15

Бренды по названию

Популярные бренды

LOFTNESS 15, Руководство пользователя и каталог запасных частей

Результаты поиска

Содержание 15

Отзывы:

Похожие инструкции для 15

Бренды по названию

Популярные бренды