manualshive.com logo in svg

LOFTNESS 15, Руководство пользователя и каталог запасных частей, Страница: 35 / 106

Поделиться
Скачать
LOFTNESS 15 Скачать руководство пользователя страница 35

27

Windrow Crop Shredder OM

Transport to Working Configuration 

Procedure (Cont'd)

Connect PTO (5) shaft to tractor.

NOTE:

 Watch length of PTO shaft. Make sure you 

have enough clearance to get by tractor's hitch 
configuration. You may need to release PTO 
shaft before connecting shredder to tractor.

 

Refer to “PTO Set-up” on page 18 for 
reference on installing and adjusting PTO shaft. 

Remove coupler ends of hydraulic hoses from storage 
rack on top of shredder.

Connect the hydraulic hoses (6) to the tractor's hydraulic 
system.

NOTE:

  Hydraulic hoses are labeled to indicate which 

coupler to connect to on the tractor's hydraulic 
system.

NOTE:

  Make sure there is enough slack in the hydraulic 

hoses to allow for sharp turns.

Retract jack and return to its storage position, securing in 
place with safety pin.

Operating Instructions

5

6

Содержание 15











































































































Отзывы:

Нет отзывов