LOFTNESS 15 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 106

LOFTNESS 15 Скачать руководство пользователя страница 46

38

Windrow Crop Shredder OM

Grease Points Location (Cont'd)

• Standard PTO CV Shaft Grease Fittings

Location: (not shown) -

Three U-joints and two

additional fittings located under the bell
housing.

Interval:

Every 8 hours of operation.

• Telescoping PTO Tube Grease Fittings

Location: (not shown) -

One located by lining up the

hole in the PTO guard with grease zerk.

Interval:

Every 25 hours of operation.

• PTO Overrunning Clutch Grease Fittings

Location: (not shown) -

Fitting located near U-joint

yoke.

Interval:

Every 50 hours of operation.

Other Lubrications Points

• Wheel Bearings

Location: (not shown) -

All wheel bearings.

NOTE:

Grease and re-pack.

Interval:

Annually.

Maintenance

Adding Oil to Gearbox

Remove the plug from the upper port (1), and the plug
from the lower port (2).

Using a funnel, add a 80W-90 gear oil into the upper port
until it runs out through the bottom port. Reinsert the plug
back into the lower port and tighten.

Return the remaining plug back into the upper port and
tighten.

Wheel Spacing Adjustment

To obtain the best results from the shredder, wheel
spacing should conform to crop row spacing. To adjust
wheel spacing, raise shredder and install blocks under
shredder end plates.

Loosen wheel strut clamping bolts (1) and adjust wheels
to desired spacing.

NOTE:

The center plate of shredder should ride in
center between crop rows.

1

1

2

«
...
44
45
46
47
48
...
»

Содержание 15











































































































Отзывы:

Нет отзывов