manualshive.com logo in svg

LOFTNESS 15, Руководство пользователя и каталог запасных частей

Поделиться
Скачать
LOFTNESS 15 Скачать руководство пользователя страница 31

23

Windrow Crop Shredder OM

Deflector Angle Adjustment

Adjustments can be made to control the windrow as it 
comes out of the machine. Adjusting position of bolt (1) 
lowers or raises the fingers on the deflector to control the 
material. The rod deflector is designed to get the material 
to the ground quickly while letting the forced air escape.

Wet, heavy material may start to plug between the rods if 
the angle is too steep.

Raise

 the fingers for wet, heavy material.

Lower

 the fingers for dry, light material.

CAUTION: 

Make sure fingers on deflector are 

lowered and do not extend beyond the 
operation wheels when transporting.

Transport to Working Configuration 

Procedure

If equipped, follow this section for proper instructions 
to safely convert the windrow shredder from a transport 
configuration to a working configuration.

Remove the linchpin (1) and safety lock pin (2) on the 
operating hitch. 

Lower the hitch using the hand winch (3) until the hitch 
braces (4) can rotate up and through the hitch frame.

1

2

1

Operating Instructions

3

4

Содержание 15











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды