LOFTNESS 15 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 106

LOFTNESS 15 Скачать руководство пользователя страница 91

83

Windrow Crop Shredder OM

Parts Identification

Machine Decals and Signs

NOTE:

All safety related decals are also shown in the
Safety Instructions Section along with their
location on the machine. See “Safety Decal
Locations” on page 9.

Check and replace any worn, torn, hard to read or missing
decals on your machine.

NOTE:

To order a complete Windrow Crop Shredder
Decal Kit use part number N34593 for 15' and
20' models, and N34591 for the 20' w/Transport
model.

Part No. N17013

Part No. 4334

WARNING

Due to the possible danger of flying debris,

it is absolutely MANDATORY that impact-resistant

shielding be provided on the power unit to

protect the operator.
The owner is responsible for providing the

operator protection devices on the power unit.

Part No. N22763

Part No. 4189

Part No. 4256

Part No. 4135

WARNING

Read and understand

operator’s manual before

using this machine.

Failure to follow operating

instructions could result

in death or serious injury.

DO NOT START, OPERATE, OR WORK ON THIS
MACHINE UNTIL YOU HAVE CAREFULLY READ
AND THOROUGHLY UNDERSTAND THE
CONTENTS OF THE OPERATOR'S MANUAL.
NOTE: IF YOU DO NOT HAVE AN OPERATOR'S
MANUAL, CONTACT YOUR DEALER OR

LOFTNESS SPECIALIZED EQUIPMENT
650 SOUTH MAIN
HECTOR, MN 55342
1-800-828-7624

FAILURE TO FOLLOW SAFETY, OPERATING, AND
MAINTENANCE INSTRUCTIONS COULD RESULT
IN DEATH OR SERIOUS INJURY TO THE
OPERATOR OR BYSTANDERS, POOR
OPERATION, AND COSTLY BREAKDOWN.

CAUTION

WARNING

Rotating parts hazard.

Can cause serious

injuries or death.
Do not operate machine

without shields attached.

PN 4189

DANGER

STAY BACK

KEEP HANDS AND FEET

AWAY FROM ROTATING

KNIVES UNDER MACHINE.

DO NOT LEAVE

OPERATOR'S POSITION

WHILE PTO IS ENGAGED

AND TRACTOR IS RUNNING.

Part No. N23931

Part No. 203264

«
...
89
90
91
92
93
...
»

Содержание 15











































































































Отзывы:

Нет отзывов