LOFTNESS 15 Скачать руководство пользователя страница 24

Страница: 24 / 106

Windrow Crop Shredder OM

Equipment Set-up (Cont'd)

Attach the wing top to the tail by inserting a 1/2" x 1-1/4"
carriage bolt and 5/8" flat washer from the bottom up
through the top (3 each side).

From the top, add a 1/2" flat washer and 1/2" lock nut
(3 each side).

IMPORTANT:

Do not tighten the hardware completely.

Repeat procedure on opposite side.

Underside view of the wing top, showing the 1/2" x 1-1/4"
carriage bolts and 5/8" flat washers installed into the tail.

On the outer end of each wing top, add the remaining
1/2" x 1-1/4" hex bolts, 1/2" flat washers and 1/2" lock
nuts (6). (Left side shown)

IMPORTANT:

Do not tighten the hardware completely.

Repeat procedure on opposite side.

Rotate the wings (7) down on both sides. (Left side
shown).

Attach the rear wing door (8) sections with 5/8" x 1-1/2"
hex bolts, 1/2" flat washer, and 1/2" lock nuts (2 per side).

The top lugs fit between the notches cut into the top edge
of the wings.

IMPORTANT:

Do not tighten the hardware completely.

Set-up Instructions

Содержание 15











































































































Результаты поиска

Содержание 15

Отзывы:

LOFTNESS 15, Руководство пользователя и каталог запасных частей, Страница: 24 / 106

Результаты поиска

Содержание 15

Отзывы: