background image

 

 

78 

16.3

 

BURNER REMOVAL 

 

If it has been determined that the flame picture is unacceptable, the burner can be removed and cleaned using the 
following procedure: 

 

1.

 

Isolate the electrical and gas supplies to the heater. 

2.

 

Allow the boiler to cool down. 

3.

 

Disconnect the wiring connections to the ignition electrode. 

4.

 

Disconnect the power and control connection leads and earthing wire from the combustion fan. 

5.

 

Apply a suitable release oil to the 6 studs around the edge of burner door. 

6.

 

Remove the 6 retaining nuts around the edge of the burner door. 

NOTE:  Once loosened, the nuts should be removed by hand.  If any of the nuts seize, the nut should 

gently be re-tightened and additional release oil used. 

7.

 

Withdraw the heat exchanger front plate and burner assembly from the heat exchanger complete with 
the combustion fan. 

8.

 

With  the  burner  assembly  away  from  the  boiler,  the  burner  can  be  gently  cleaned  with  the  brush 
attachment of a vacuum cleaner. 

 

The reassembly procedure is the reverse of the above taking care to ensure that the for the heat exchanger front 
plate  sealing  gasket,  the  combustion  fan  connection  gasket,  the  burner  door  insulation  and  the  combustion 

chamber rear wall insulation are in good condition or are replaced as necessary. 
 

When refitting the burner door, the door should be carefully located on the studs and pushed firmly in to 

place whilst all of the retaining nuts are tightened by hand. Once all  nuts are hand tight, they should be 
tightened in the order stated in Figure 16.1 to a torque of 8 Nm 

 

 

NOTE:  PARTICULAR  ATTENTION  SHOULD  BE  PAID  TO  THE  COMBUSTION  CHAMBER  REAR  WALL 

INSULATION.    IF  ANY  DETERIORATION  IN  THE  INSULATING  MATERIAL  IS  NOTED,  THE 

INSULATION PANEL MUST BE REPLACED. 

 

 

FIGURE 16.1 

BURNER DOOR RETAINING NUT TIGHTENING ORDER 

 
 

 

Содержание CP-M Series































































































Отзывы: