CHAPTER 8: MALFUNCTIONS/MAINTENANCE
113
QUICK LOAD SERVO S3T
2.
MAINTENANCE
Please read the safety instructions provided at the beginning of this manual before
handling the following devices.
2.1. Pneumatics
The air unit filter is equipped with an automatic drain valve, avoiding the need to empty it. The water
recuperated comes from the pneumatic circuit of the building. It is recommended that steps are taken to
ensure the air supplied to the bar feeder is as dry as possible (see CHAPTER 5: PNEUMATICS).
2.2. Batteries
In the event of a power failure, a backup battery saves the data contained in the PLC. It is possible that
with time this battery will slowly drain; in this case a message will be displayed on the remote control. The
battery must be replaced as soon as possible with a battery of the same type.
Switching off the bar feeder when the message “Battery low” is displayed may wipe the
parameters. Do not switch off the power until the battery has been replaced.
2.3. Belt
It is possible that after a certain amount of use, the bar feeder belt will require tensioning.
Refer to chapter 6. GENERAL DESCRIPTION, section 6. BELT.
2.4. Cleaning
Regular cleaning of your bar feeder can only serve to improve its operation and prolong its useful life.
To clean the outside, use a soft cloth and a regular detergent; for the inside, use a cloth or a brush
soaked in petrol or benzine. However, make sure that the rollers and parts made of synthetic materials do
not come into contact with these products.
The use of compressed air for cleaning is not advisable, because particles could become lodged in
sensitive areas and compromise the operation of the bar feeder.
At no time should solvents, such as acetone or thinners be used for cleaning the bar
feeder. At no time should cleaning products come into contact with electrical components.
2.5. Spare parts
Unless written consent is provided by LNS, no addition or modification may be made to the
machine or its spare parts.
LNS cannot be held liable if spare parts not provided by LNS are used.
Содержание SERVO S3 T
