LNC LNC-T800 Скачать руководство пользователя страница 99

Страница: 99 / 100

LNC-T800

LNC Controller Operation Instruction

LNC Technology Co., Ltd.

2.11 Parameter Setting

The method of parameter setting is as the following:

1. Make sure machine is currently in the status of preparation done.

2. Switch to <PARAM> group.

3. Click

【

NC.SYS

】

function button to switch to parameter screen.

4. Use Up, Down, Right, Let buttons to move cursor to the parameter to be set. If the serial number of the

parameter to be edit is known, input Pxxxx in input line, and click INPUT button to position to the

parameter. The xxxx represents the serial number of the parameter.

5. After moving to the parameter, input desired values in input line, and click <INPUT>.

6. A box asking for a password appears. Input correct password to proceed to parameter modification.

7. Default value of password is 0000. The password can be changed. Please well remember the changed

password, if not, parameters will not be able to be changed.

2.12 Backup System Parameters

It is recommended to backup machine setting parameters after machine adjustment is done. The method to

backup parameters is as the following:
1. Prepare an empty disk, make sure it’s not write-protected, and scan it for virus at first. Insert it to FDD.

2. Click emergent stop to let machine enter the NO-RDY status.

3. Switch to <DGNOS> group.

4. Click

【

SUSUPD

】

function button to switch to system upgrade operation screen.

5. Use UP, Down buttons to move cursor to PARAM BACKUP position, and click

【

】

button.

6. Click

【

ALL

】

function button to select all parameter categories and click

【

】

button.

7. Use UP, Down buttons to move cursor to GENERAL DISK/NET Method and click

【

】

button.

8. Clear the displayed folder path, and input A:\. Click

【OK】

button to start backup parameters. When the

backup is done, a prompt appears in prompt line.

Содержание LNC-T800





































































































Результаты поиска

Содержание LNC-T800

Отзывы:

Похожие инструкции для LNC-T800

Бренды по названию

Популярные бренды

LNC LNC-T800, Руководство оператора

Результаты поиска

Содержание LNC-T800

Отзывы:

Похожие инструкции для LNC-T800

Бренды по названию

Популярные бренды