LNC LNC-T800 Скачать руководство пользователя страница 92

Страница: 92 / 100

LNC-T800

LNC Controller Operation Instruction

LNC Technology Co., Ltd.

2.1.2.2

Copy File from Controller to Disk

Instructions are as the following:

1. Switch to Edit Mode (EDIT), and make sure machine is currently in the status of preparation done.

2. Switch to <PROG> module.

3. Click

【

DIRMNG

】

function button to switch to File Manager screen.

4. Insert the disk containing part programs to FDD.

5. Click

【

COPY C>A

】

function button, and a list of files in the controller will be displayed. Move cursor to the

file to be copied, and click

【

】

6. After

clicking

【

】

button, the destination file use the source file’s name as the default file name, if want

to use a different file name, manually input the name and click

【

】

button to finish copy.

2.1.2.3

Copy File to Controller from Any Source

Instructions are as the following:

1. Switch to Edit mode and make sure machine preparation is done.

2. Switch to <PROG> module.

3. Click

【

DIRMNG

】

function button to switch to the screen of File Manager.

4. Click

【

COPY

】

function button, after clicking this function button, a dialog box appears on screen. Use Up,

Down, Right, Left to move cursor to source file. FDD and online drive can also be the file source. Click

【

】

after selection.

5. File name of the target file will be the same as the source file. If want to use a different name, input the

name and click

【

】

to finish copy process. After copy, users can use program list to check result.

2.1.3

Delete File

Instructions on Delete File are as the following

：

1. Switch to Edit mode and make sure machine preparation is done.

2. Switch to <PROG> module.

3. Click

【

DIRMNG

】

function button to switch to the screen of File Manager.

4. The Delete File function button is on the 2

page of File Manager. Therefore click Next Page at first to

find the function button.

5. Click

【

DEL

】

, and then file list is displayed. Select the file to be deleted, and click

【

】

6. A message box for users to confirm the deletion appears. If surely to delete file, click

【

】

to finish the

process of Delete File. After delete, users can use program list to check result.

Содержание LNC-T800





































































































Результаты поиска

Содержание LNC-T800

Отзывы:

Похожие инструкции для LNC-T800

Бренды по названию

Популярные бренды

LNC LNC-T800, Руководство оператора

Результаты поиска

Содержание LNC-T800

Отзывы:

Похожие инструкции для LNC-T800

Бренды по названию

Популярные бренды