manualshive.com logo in svg

LinMot B1100 Series, Руководство пользователя

Поделиться
Скачать
LinMot B1100 Series Скачать руководство пользователя страница 78

 

L

 

i

 

n

 

M

 

o

 

t

 

 

Motion Control SW

7.4 Monitoring

All drive series support enhanced monitoring features of the supply voltages and the board 
temperatures.

7.4.1 Logic Supply Voltage

The logic supply voltage must be in the range from 20V to 28V when using the default 
parameter settings. If the supply voltage goes out of this range, an error will be generated. If 
the supply voltage goes below approx. 18V the drive shuts down.

Parameter Name

UPID

Description

Logic   Supply 
Voltage Too Low

100Eh

If the logic supply voltage sinks below this limit the error 01h 
will be generated.

Parameter Name

UPID

Description

Logic   Supply 
Voltage Too High

1010h

If the logic supply voltage rises above this limit the error 02h 
will be generated.

7.4.2 Motor Supply Voltage

The motor supply voltage can be monitored with different warn and error levels.

Parameter Name

UPID

Description

Motor   Supply 
Voltage Low

1018h

If the motor supply voltage sinks below this limit the warn bit 
Motor Supply Voltage Low (bit 2) is set.

Motor   Supply 
Voltage High

1019h

If the logic supply voltage rises above this limit the warn bit 
Motor Supply Voltage High (bit 3) is set.

Parameter Name

UPID

Description

Motor   Supply 
Voltage Too Low

101Ah

If the logic supply voltage sinks below this limit the error 03h 
will be generated.

Motor   Supply 
Voltage Too High

101Bh

If the logic supply voltage rises above this limit the error 04h 
will be generated.

7.4.2.1 Phase Switch On Test

The parameters in the Phase Switch On Test section are used in the HW Tests State (State 
5) before enabling the power stage. If the motor power supply is on and there is no ground  
path in the motor (inclusive cabling) the phase voltage is approx. 6.5V when in power off 
state. When moving the motor the induced voltage may lead to HW test error.

Parameter Name

UPID

Description

Phase   Voltage 
Low Level

102Ch

If   one   of   the   phase   voltages   is   below   this   limit   before 
powering up an error will be generated.

Phase   Voltage 
High Level

102Dh

If   one   of   the   phase   voltages   is   above   this   limit   before 
powering up an error will be generated.

Page 78/91

User Manual Motion Control SW / 06/12/2013

NTI AG / LinMot

Содержание B1100 Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды