Linkam Scientific Instruments FDCS196 Скачать руководство пользователя страница 2

Страница: 2 / 40

Contents

Before Setting Up Your Equipment…………………………………………………………………..………………….3

Important Notice...................................................................................................................4

Warranty..............................................................................................................................4

Technical Support.................................................................................................................4
Equipment Maintenance........................................................................................................4
Handling Liquid Nitrogen.......................................................................................................4

Feedback..............................................................................................................................4

Safety Precautions................................................................................................................5

Symbol Reference.....................................................................................................5

Introduction..........................................................................................................................6

THMS600 Stage Specification.....................................................................................6

THMS600 System..................................................................................................................6

Stage Anatomy.....................................................................................................................7

Stage Assembly.........................................................................................................7

Lid Assembly.............................................................................................................7

Mounting Stage to Microscope with Dovetail Substage.............................................................8

Setting up the Condenser......................................................................................................8

Vacuum Tweezers.................................................................................................................9
Connecting the Instruments.................................................................................................10

T95 System Controller Cable Connections.........................................................................10

LNP95 Cooling Pump Connection.....................................................................................11

Remove Transit Screws............................................................................................11

Back Panel Cable Connection....................................................................................11

Connecting the Pirani Gauge………………………………………………………….………………………………...12

Flexible Stainless Steel Vacuum Tube Connection……………………..………………………………………..13

FDCS196 Pro System Setup…………………………………………………………….………………………………..14

Edwards Vacuum Pump Setup………………………………………………………………………….…………..14

MV196 Motorised Valve System Setup…………………………………………………………………..……...14

Mounting the MV196………………………………………………………………………………………………..….14

Sample Preparation and Loading..........................................................................................15

Sample Loading Using G16.3 Sample Holder………………………………………………………………....15

Sample Loading Using FDCS196/CC Crucible Carrier and Quartz Crucible............................18

Cooling Connections............................................................................................................21

Using The FDCS196 System……………………………………………………………………………………………...22

Programming Temperature………………………………………….……………………...……………………….22

Using Linksys32 Software to Control MV196 Motorised Valve…………………………………………..22

Set Vacuum…………………………………………………………………………………………..…………………...22

Using T95-

LinkPad to Control MV196 Motorised Vacuum Valve…………………………………….....23

Vacuum Parameters…………………………………………………………………………………………………….24

Running a Profile with Vacuum…………………………………………………….…………………..…………..25

Appendix............................................................................................................................26

Using The Stage with Gas Connectors...................................................................................26

Installing Gas Connectors……………………………………………………………………………………………..26

FDCS/CC Crucible Carrier and Quart Crucible.....................................................................27

Cooling Connections........................................................................................................29

Purging Procedure…………………………………………………….………………………………………..……….30

Spares and Accessories........................................................................................................34

Troubleshooting..................................................................................................................36

Contact Details....................................................................................................................40

Содержание FDCS196









































Результаты поиска

Содержание FDCS196

Отзывы:

Бренды по названию

Популярные бренды

Linkam Scientific Instruments FDCS196, Руководство пользователя

Результаты поиска

Содержание FDCS196

Отзывы:

Бренды по названию

Популярные бренды