24 SET FADE?
Setting a fade time to a channel will slow down any level change received at the input. This enables smooth
fade effects from simple switched inputs or may be used to protect the dimmer load from instantaneous level
changes. Selected fade time applies to both fade in and fade out. NOTE: In this menu the fade time is applied
to an individual channel and not a complete scene as in menu 35.
241 CHANNEL [n]
∧
∧
/
∨
∨
to select channel and press
4
.
2411 TIME [n]
Default = 1 (minimum).
∧
∧
/
∨
∨
to set fade time and press
4
.
Available fade times are approximately 0, 1.2, 3, 4, 7, 133, 165, 220, 330 seconds.
3 SET SCENES?
The user may program a total of eight scenes, 1-8, by recording the current dimmer pack output. Dimmer output can
be achieved by recording incoming DMX/analogue signals and/or preheat level settings. Scenes may be replayed
using either the front panel controls or Preset control inputs.
Press
4
.
∧
∧
/
∨
∨
to select the attribute to change and press
4
.
31 REPLAY?
Select a previously recorded scene or programme chase to output.
311 GO [ n]
∧
∧
/
∨
∨
to select a scene or chase and press
4
.
⇒
OUTPUT OK
32 RECORD?
Save the current dimmer output to one of the 8 scene memories or access wall plate programming mode
.
321 GET SCENE [n]
∧
∧
/
∨
∨
to select scene numbers 1-8 or R (for remote programming, see page 5).
Press
4
to capture current dimmer output.
⇒
STORED OK
33 DMX FAIL?
The following options are selectable in the event that the DMX input to the dimmer fails or is removed. This is
only applicable when DMX is a selected input source.
331 [ ]
Default = LAST HELD
Choose from:
LAST HELD
the last signal received is held in the outputs.
GO NO DMX
the NO DMX SCN scene is output.
SCENE 8
a user-programmed scene is output.
GO ANALOG
the Paradime looks for an analogue input signal.
SCN8+WP
the Paradime outputs scene 8. Control from any connected WP6 wall plate is also
active.
ALL OFF
all channels go to 0 output.
∧
∧
/
∨
∨
to desired option and press
4
to store.
⇒
STORED OK
34 MAP INPUTS?
Pins 1-6 of the analogue input connector can be used to access the Preset inputs and may be mapped to any
of the stored scenes 1-8 and/or programmed chase/speeds 10-99.
341 CHANNEL [n]
∧
∧
/
∨
∨
to select one of the six available presets and press
4
.
3411 DO [ ]
∧
∧
/
∨
∨
to select one of the available scenes or chase programs chases for this channel number
and press
4
.
35 FADE TIMES?
In a similar way to individual channels, the scenes 1-8 may be set to automatically fade in/out over a set
period of time. This is useful for 'seamless' level changes in some architectural lighting applications. Fades
between scenes are 'dipless'. NOTE: In this menu the fade time is applied to the complete scene and not an
individual channel as in menu 24.
351 SCENE [n]
∧
∧
/
∨
∨
to select scene and press
4
.
3511 [00m 00s]
∧
∧
/
∨
∨
to set the desired fade time for the scene and press
4
.
⇒
STORED OK
MENU SYSTEM AND USER OPTIONS - cont’d
LightProcessor Paradime, all variants, version 21, September 2003
Page 7
