LiftEquip TW160 Скачать руководство пользователя страница 9

Страница: 9 / 112

Operating manual

Safety

TW160 drive

TK Aufzugswerke

Version 08/2021

2.2

Safety requirements

This document contains important information for safe operation of the product.



Keep this document and all other applicable documents at the location of use for
the entire working life of the product.

2.2.1

Area of applicability

This document applies only to the product described here.

Other applicable documents



International occupational health and safety regulations

2.2.2

Basic requirements for safety



All existing safety devices are to be tested regularly in accordance with the

maintenance schedule.



This document, in particular the chapter entitled “Safety", together with the
warning notes and all other applicable documents must be observed by all
persons who work with the product.



Supplementary to this document, the rules at the location of use with regard to

environmental protection, and the regulations of work safety and accident
prevention must be observed.



All safety and hazard notices on the installation must be kept in legible condition.



Safety information and instructions required by law must be displayed to users in

plain view.



A requirement for safe handling and non-disruptive operation of this product is

knowledge of the fundamental safety regulations.

2.2.3

Obligations of the operating company and installation firm



Only deploy trained and instructed qualified personnel.



Provide personnel with the required personal protective equipment.



Check personnel at regular intervals to ensure that they follow safety-conscious
work practices and comply with national provisions.



Make all other applicable documents as well as this document available to
personnel.

2.2.4

Duties of personnel



Clearly establish all areas of responsibility prior to any activity.



Always wear the personal protective equipment made available to you.

Содержание TW160

















































































































Результаты поиска

Содержание TW160

Отзывы:

Похожие инструкции для TW160

Бренды по названию

Популярные бренды

LiftEquip TW160, Руководство по эксплуатации

Результаты поиска

Содержание TW160

Отзывы:

Похожие инструкции для TW160

Бренды по названию

Популярные бренды