Lift Tek 35DV-MQ Скачать руководство пользователя страница 43

Страница: 43 / 48

Page 4

263920 R

ervice

5.5-6

Mast Skewing Adjustment

Extend the mast to full lift height (see Figure 47).

* If the mast bends to the right at full extension,

a shim(s) needs to be removed from the left

main lift cylinder rod.

* If the mast bends to the lift at full extension,

a shim(s) needs to be installed on the left

main lift cylinder rod.

Place a 4 X 4 X 20 in. (10 X 10 X 50 cm) wood block

between the outer intermediate and outer upright

crossmembers (see Figure 46). Lower the Mast

uprights onto the block.

Remove the snap ring from the left-hand cylinder rod.

Open the truck valve to allow the cylinder rod to retract.

Tap the cylinder rod down past the outer intermediate’s

top crossmember. Install or remove shim(s) on the

cylinder rod, below the crossmember (see Figure 46).

Shim are listed below:

Shim Thickness

Part No.

.010 in. (.25 mm)

205198

.031 in. (.79 mm)

205199

.062 in. (1.57 mm)

205196

.092 in. (2.36 mm)

205197

Slowly hydraulically power the main lift cylinder rod up

into the crossmember and reinstall the snap ring.

Repeat steps 1 through 4 until skewing is removed.

WARNING:

The upright must be supported

by a block to avoid possible injury.

MA0261.eps

Right Hand

Main Lift

Cylinder

Left Hand

Main Lift

Cylinder

Free Lift

Cylinder

Outer

Intermediate

Upright

4 x 4 in.

(10 x 10 cm)

Wood Block

Outer

Upright

MA0260.eps

Snap

Ring

Shim

Figure 46. Blocking upright to retract

LH main lift cylinder rod.

Figure 47. Extending Mast to check

for skewing (driver’s side).

Содержание 35DV-MQ

















































Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды

Lift Tek 35DV-MQ, Руководство по обслуживанию

Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды