manualshive.com logo in svg

Lift Tek 35DV-MQ, Руководство по обслуживанию, Страница: 11 / 48

Поделиться
Скачать
Lift Tek 35DV-MQ Скачать руководство пользователя страница 11

263920 R

2

Page 11

I

nstallation

2.4-2

Internal Reeving

STANDARD 

( Continued )

Lower 

Hose 

Guide

 

Inner 

Upright 

Bracket 

Inner 

Intermediate

Upright Sheave

 

SINGLE 

FUNCTION 

DOUBLE 

FUNCTION 

MA3156.eps

8

15

8

SINGLE

FUNCTION

DOUBLE

FUNCTION

Carriage

Bracket

Fittings

15

20

16

18

SINGLE 

FUNCTION

 

DOUBLE 

FUNCTION 

BACK VIEW

13

MA3157.eps

SINGLE 

FUNCTION

 

DOUBLE 

FUNCTION 

BACK VIEW

13

MA3157.eps

Connect 

hoses

11

Short

Hose

9

Long

Hose

Short

Hose

Long

Hose

Short

Hoses

Long

Hose

Long

Hose

13.

 Position the hoses with the tabs on the inner upright

bracket as shown in figure 13.

14.

 Install the lower IHR cover plate and hardware.

Tighten the capscrews to 30 ft-lbs (41 Nm).

15.

 Route the hoses up toward the top of the mast

following the inner lift chains. Bend the hoses over

the inner intermediate upright sheave and install the

sheave on the shaft bolted to the intermediate

upright. Install washer and retaining ring to shaft.

16.

 Route the hoses down to the lower hose guide.

Place hoses under the hose clamp at the top of

the lower hose guide. Pull downward on the hoses

with 20 lbs. of force. Tighten clamp capsrews

enough to stop hose movement.

17.

 Install the upper hose guide to the outer upright.

Tighten the capscrew to 30 ft-lbs. (41 Nm).

18. 

Loop the hoses approximately 5 in. (125mm)

below the bottom of the lower hose clamp and

rout upward into the upper hose guide.

Figure 13. Installing internal hose reeving on uprights.

Содержание 35DV-MQ

















































Отзывы:

Нет отзывов