Lift Tek 35DV-MQ Скачать руководство пользователя страница 39

Страница: 39 / 48

Page 3

263920 R

ervice

5.5-5

Upright Reassembly

Lubricate the full length of the outer upright rails with

chassis lube or Kendall SR-12X (see Figure 39).

Attach an overhead hoist to the outer intermediate

upright and install it through the top of the outer

upright. Position it out the lower end of the outer upright

about 6 in. (15 cm).

Assemble shims, load rollers and thrust blocks to the

upper end of the outer upright. Assemble shims and

load rollers to the lower end of the outer intermediate

upright.

Roller Shimming -

Install shims to provide a total side-

to-side clearance of 1/16 in. (1.5 mm) max. at the

tightest point throughout the travel of the upright (see

Figure 40). Pry between the upright and the load roller so

that the opposite load roller is tight against the upright.

Measure the clearance for the pair of rollers at the XXX

shown. Use an equal number of shims on each side.

NOTE:

Roll the uprights past installed thrust plugs/

blocks before checking load roller clearance.

Thrust Plug/Block Replacement -

Install thrust plugs/

blocks to provide a clearance of 1/16 in. (1.5 mm) max.

between an upright and its corresponding thrust plug/

block (see Figure 41). Pry between the upright upper

crossmembers. Measure the clearance at the XXX

shown to determine which thickness thrust plug/block to

use. Thrust plugs/blocks may be shimmed as required.

Lubricate the full length of the outer intermediate

upright rails with chassis lube or Kendall SR-12X

(see Figure 40).

Figure 40. Channel lubrication area, load roller clearance

measurement.

Upright

Rails

MA0259.eps

.06 in.

(1.5 mm)

Max.

Load

Rollers

Upright

Rail

Lube

Shim

1 4

Outer

Intermediate

Upright

MA0246.eps

Inside

of Rail

Thrust

Block

Outer

Upright

.06 in.

(1.5 mm)

Max.

Thrust

Block

Thrust

Plugs

Figure 41. Installing outer intermediate upright.

Содержание 35DV-MQ

















































Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды

Lift Tek 35DV-MQ, Руководство по обслуживанию

Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды