Lift Tek 35DV-MQ Скачать руководство пользователя страница 33

Страница: 33 / 48

Page 3

263920 R

ervice

5.5

Mast Uprights

Figure 34. Exploded View of Mast Uprights.

5.5-1

Upright Description

Outer Upright Assembly

The outer upright assembly is mounted to the truck. A pair
of shim-adjustable load rollers are attached to stub shafts

located near the top of the upright. A pair of adjustable

main lift chain anchors attached to bosses on each inner side

of the upright. Two main lift cylinders, one on each side, sit

in bosses on the back of the upright,

Outer Intermediate Upright Assembly

The outer intermediate upright assembly telescopes
within the outer upright assembly. A pair of shim-

adjustable load rollers are attached to stub shafts located

at the top and bottom of the upright. A pair of chain

sheaves are located near the top of the upright to provide

a rolling surface for the outer main lift chains.

Inner Intermediate Upright Assembly

The inner intermediate upright assembly telescopes within

the outer intermediate upright assembly. A pair of shim-

adjustable load rollers are attached to stub shafts located

at the top and bottom of the upright. A pair of chain

sheaves are located near the top of the upright to provide a

rolling surface for the inner main lift chains. A hose sheave

is located next to the chain sheave to provide a rolling

surface for the free lift cylinder supply hose.

Inner Upright Assembly

The inner upright assembly telescopes within the inner

intermediate upright assembly. A pair of shim-adjustable

load rollers are attached to stub shafts located at the

bottom of the upright. The free lift chain anchors are

attached to the center crossmember and the main lift chain

anchors are attached to the lower end of each of the upright rails.

The free lift cylinder sits on a platform which is intergal with

the lower crossmember. The free lift chain crosshead and

sheaves mount on top of the free lift cylinder.

MA0243.eps

Inner

Intermediate

Upright

Hose

Sheave

Chain

Sheave

Load

Roller

Chain

Anchor

Inner

Upright

Crosshead

Outer

Intermediate

Upright

Outer

Upright

Содержание 35DV-MQ

















































Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды

Lift Tek 35DV-MQ, Руководство по обслуживанию

Результаты поиска

Содержание 35DV-MQ

Отзывы:

Похожие инструкции для 35DV-MQ

Бренды по названию

Популярные бренды