30
206-4256
Installer Menu (Cont.)
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. The factory default is 0, which provides the full
range of volume control, if item 009 MAX VOLUME is set to 63. It
is recommended to set the same value on every STB.
Note:
The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb
others. The value range is 0 to 63, with 63 as the default, which
gives the user the full range of volume control, if item 008 MIN
VOLUME is set to 0. It is recommended to set the same value on
every STB.
Note:
The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted. If set to 0, sound can be muted.
011 - KEY DEFEAT
Applicable for LG Hospitality and commercial non-LG display
panels only. If set to 1, Key Defeat is enabled, which means that
end users cannot access or navigate within the STB’s on-screen
menu(s) using the display panel button(s); e.g., SETTINGS, OK,
and menu navigation buttons will not function. Set to 0 to disable
Key Defeat.
Note:
Users can always access the STB’s menus by pressing
MENU on the remote.
Note:
This feature does not apply to LG Public Displays or LG
Commercial Monitors since the STB will always disable those
displays’ panel buttons and the processing of IR.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN. TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
Note:
The STB clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, the Alarm function is available to the end
user. Set to 0 to disable the Alarm function.
Note:
The STB clock must be set before the Alarm function will
work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the STB will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-STB/display single room installation. First
determine the IR mode; then select the bed number.
Values
IR Mode
Bed #
0
Disabled
N/A
16 – 24
Multi-code Remote
1 – 9
Note:
The STB-dedicated Installer Remote is required for use of
this feature. For further information, see Reference section, “STB
Installer Remote.”
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to filter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
Note:
This item is not available in the Installer Menu when item
021 V-CHIP is set to 0 or when item 084 PERMANENT BLK is set
to 1.
023 - CAPTION LOCK
If set to 0, captions are OFF when the STB/display panel is turned
ON. Set to 1 to use the caption setting configured before the STB/
display was turned OFF when the STB/display is turned ON.
028 - CH. OVERIDE (Channel Override)
Applicable for Pass-through Mode only.
If set to 1, users can select
channels either with Channel Up/Down or by direct keypad entry.
This setting also allows full access to channel settings in the STB
setup menus (i.e., channels may be added or removed from the
channel lineup, channel labels and icons may be edited, etc.). If set
to 0, the channel lineup is locked. That is, user access to channel
settings in the STB setup menus is restricted, and users can only
tune to the channels that are included in the channel lineup. Also, in
this case, if the channel lineup has not been transferred to the PTC
(via 2-5-5 + MENU Mode, as described in the Master STB Setup
procedure), users can only select channels using Channel Up/
Down; direct keypad entry is not available.
029 - OLD OCV (On Command Video™)
Set to 1 to remap the PTC’s direct tune channels for Aux inputs
from 13x to 9x. This allows 2-digit only tuning systems (i.e., legacy
OCV) to direct tune Aux inputs. See also Reference section, “STB
Aux Input Configuration.”
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.