LG MultiSITE MS8250 Скачать руководство пользователя

Страница: 4 / 80

MultiSITE MS8250 V

AV Room Controllers

Due to our policy of continuous product innovation, some specifications may change without notification.

SAFETY PRECAUTIONS

TABLE OF SYMBOLS

DANGER

This symbol indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

This symbol indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

This symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

This symbol indicates situations that may result in equipment or property damage accidents only.

This symbol indicates an action that should not be performed.

The instructions below must be followed to prevent product malfunction, property damage, injury or death to the user or other people. Incor-

rect operation due to ignoring any instructions will cause harm or damage. The level of seriousness is classified by the symbols described

below.

DANGER

Do not use or store flammable gas or combustibles near

the unit.

There is risk of fire, explosion, and physical injury or death.

Disconnect power before installing or servicing the unit.

There is risk of physical injury or death due to electric shock.

Do not touch any exposed unit wiring, terminals, or other

electrical components with tools or exposed skin. Only quali

fied technicians should install, use, or remove this unit.

Improper installation or use may result in fire, explosion, electric shock,

physical injury and/or death.

WARNING

The information contained in this manual is intended for use

by an industry-qualified, experienced, trained electrician

familiar with local, national, and regional codes and who is

equipped with the proper tools and test instruments.

Failure to carefully read and follow all instructions will result in personal

injury or death.

All electric work must be performed by a licensed electrician

and conform to local building codes or, in the absence of lo

cal codes, with the National Electrical Code, and the instruc

tions given in this manual.

If the power source capacity is inadequate or the electric work is not

performed properly, it will result in fire, electric shock, physical injury or

death.

Do not change the settings of the protection devices.

If the protection device is shorted and forced to operate improperly, or

parts other than those specified by LG are used, there is risk of fire,

electric shock, explosion, and physical injury or death.

Discharge yourself correctly before handling and installing

the controller.

There is risk of electric shock and physical injury or death.

Do not touch the unit with wet hands.

There is risk of fire, electric shock, physical injury, and/or death.

This manual provides details on configuring the LG MultiSITE MS8000 Series Room Controllers to monitor and control LG HVAC equipment

(Model Number: VUCQMS8250).
Refer to the Installation Manual for installation and mounting instructions of the controllers.

Содержание MultiSITE MS8250

















































































Результаты поиска

Содержание MultiSITE MS8250

Отзывы:

Похожие инструкции для MultiSITE MS8250

Бренды по названию

Популярные бренды

LG MultiSITE MS8250, Руководство пользователя

Результаты поиска

Содержание MultiSITE MS8250

Отзывы:

Похожие инструкции для MultiSITE MS8250

Бренды по названию

Популярные бренды