LG Multi V ARUN053GF2 Скачать руководство пользователя страница 45

Страница: 45 / 76

Electrical W

iring

Due to our policy of continuous product innovation, some specifications may change without notification.

Figure 48: Accessing the Power Wiring and Communi-

cation Cable Connections.

Capacity of Power Supply Wiring (current)

Recommended Minimum Distance

1,2

100V or more

10A

12 inches

50A

20 inches

100A

40 inches

Exceed 100A

60 inches

The figures above are based on parallel lengths up to 328 feet long. For lengths in excess of 328 feet, the distances will have to be recalculated in

direct proportion to the additional line lengths involved.

If the power supply waveform continues to exhibit some distortion, the space between the power wiring and communication cable should be increased.

•

Position the power wiring a minimum of two (2) inches away from the communication cables to avoid operation problems caused by electri-

cal interference. Do not run both in the same conduit.

•

If it is necessary to run the power wiring and communication cable alongside each other and cannot be avoided, see the table below for

minimum recommended distances.

Table 26: Power Wire and Communications Cable Minimum Required Separation Minimum Allowable Distances.

•

Do not secure the power wiring and communication cables together.

•

Do not run the power wiring and the communication cable in the same conduit.

separating Power Wires and communication cables

•

All power wiring and communication cable installation must be performed

by authorized service providers working in accordance with local, state, and

National Electrical Code regulations related to electrical equipment and wiring,

and following the instructions in this manual.

•

Undersized wiring may lead to unacceptable voltage at the unit and may cause

unit malfunction and be a fire hazard.

•

Properly ground the Space II unit and indoor units. Ground wiring is required

to prevent accidental electrical shock during current leakage, communication

problems from electrical noise, and motor current leakage. Ground wiring must

always be installed by a qualified technician.

Do not connect ground wire to refrig-

erant, gas, or water piping; to lightning rods; to telephone ground wiring; or to

the building plumbing system. Failure to properly provide an National Electri-

cal Code-approved earth ground can result in equipment malfunction, property

damage, electric shock, physical injury or death.

• Install appropriately sized breakers / fuses / overcurrent protection switches and wiring in accordance with local, state, and National

Electrical Code regulations related to electrical equipment and wiring, and following the instructions in this manual. Using an over-

sized breaker or fuse may result in equipment malfunction, property damage, electric shock, physical injury or death.

•

Consider ambient conditions (temperature, direct sunlight, inclement weather, etc.) when selecting, installing, and connecting the

power wiring.

•

If the system operates in reversed phase, it may damage the compressors and other components.

•

If there is a possibility of reversed phase, phase loss, momentary blackout, or the power goes on and off while the system is

operating, install a field-supplied phase loss protection circuit.

electrIcal WIrInG

General Information

Front Panel

DIRECTION OF PIPING/WIRING

To access the power wiring / communications cable

connections, remove all of the screws on the front

panel and pull it forward.

Содержание Multi V ARUN053GF2













































































Результаты поиска

Содержание Multi V ARUN053GF2

Отзывы:

Похожие инструкции для Multi V ARUN053GF2

Бренды по названию

Популярные бренды

LG Multi V ARUN053GF2, Руководство по установке

Результаты поиска

Содержание Multi V ARUN053GF2

Отзывы:

Похожие инструкции для Multi V ARUN053GF2

Бренды по названию

Популярные бренды