LG LG A1C-A5 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 107

background image

AC Module System Installation Manual

Rev. 1.0

•

To prevent the risk of electric shock, do not touch any terminals in operation and wait for a few
minutes after turning a circuit breaker off. It may be energized in the open position.

•

To prevent the risk of overvoltage, do not disconnect the cable connector in operation.

•

Do not contact electrically active parts of the panel, such as terminals, without appropriate

safety gear. Contact may result in lethal spark or electric shock.

•

To prevent the risk of electric shock, do not touch the glass surface or frame of the solar

module after installation.

•

Do not use or install AC modules if the module is broken or torn. Failure to comply may result in

electric shock.

•

To prevent the risk of burns, do not touch AC modules during operation.

•

For safety, only qualified personnel should service modules.

•

To prevent the risk of electric shock, stay away from any damaged modules. Do not operate the
module if you find broken glass or torn back sheets in any module.

•

Damaged modules must be handled with proper safety equipment.

•

Micro inverter warranty is void if cover removed. No serviceable parts inside. Refer to qualified
personnel for service.

•

For proper operation, make sure to use AC cables, connectors and accessories provided by LG
Electronics. Parts that are not listed may cause critical danger.

•

For proper operation, the AC module shall be connected only to a dedicated branch circuit.

•

To prevent the risk of fire, do not connect any device between the AC module and circuit
breaker. Circuit breaker may not work properly.

•

Before installation, make sure to check that the area of location meets the required environment.

•

Perform all work in dry conditions and use only dry tools. Do not handle wet panels without
appropriate protection equipment.

•

Damaged modules must be treated with safety protection equipment.

•

Do not approach to the damaged or broken module unless you are an authorized or qualified
expert.

•

Wastes, electrical parts, bolts, nuts, conductors or any other debris must be cleared after
installation.

•

Do not bend AC cables. While under stress, it may occur module damage. Cable bending radius
should be more than 5 times the cable diameter, at least.

1-3 Important Safety Instructions

6

Copyright © 2017 LG Electronics.

All Rights Reserved.

«
...
4
5
6
7
8
...
»

Содержание LG A1C-A5 Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для LG A1C-A5 Series

Бренд: Thinkpower Страницы: 30

Бренд: Seneca Страницы: 4

Бренд: Mase Страницы: 22

Бренд: Viking Страницы: 4

Бренд: CEL-MAR Страницы: 16

Бренд: Perle Страницы: 23

Бренд: Inter-m Страницы: 20

Бренд: G-Power America Страницы: 55

HauteSHOT microNVR video processing platform

Бренд: Hautespot Страницы: 30

Бренд: Renaissance Learning Страницы: 2

Бренд: Comprehensive Страницы: 13

Бренд: Hoymiles Страницы: 29

Бренд: IMC Networks Страницы: 1

Бренд: IMC Networks Страницы: 8

Бренд: Asus Страницы: 18

Essence One Series

Бренд: Asus Страницы: 32

Бренд: Hegel Страницы: 8

Бренд: Craftsman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды