LG LG A1C-A5 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 107

background image

AC Module System Installation Manual

Rev. 1.0

Before Installing the AC junction box and PV rack, be aware of the following requirements:

•

Determine appropriate solar panel angle maximizing the amount of sunlight. It depends on geographical
conditions.

•

To make better air circulation along the backside of the AC module, it is recommended to install the PV
rack with a gap of at least 4 inches (100mm) between the back of the module and roof surface. It might
affect UL listing and fire class if it is less than 4 inches (100mm).

•

Install AC junction box near the AC module.

•

Install using the parts approved in the installation region.

Construct the overall frame of the solar system in the following order:

•

Install the PV rack according to the number of modules per array and the dimensions of the AC module.
(refer to Chapter 9. Product Specification)

•

Inspect the installation site and design possible combination of arrays that fits into the installation site. If
there are any vents or obstacles that make array build difficult, go to 3-9 Building an array of AC modules
to get ideas to design an array.

•

Install the AC junction box near the PV rack. Select the size and type of AC junction box suitable for
connection type according to the output voltage. (refer to 3-12 Connecting Array of AC Modules-to-
Distribution Panel)

•

Make sure that the AC junction box is under protection of weather proof function.

•

Please use appropriate conduit or ducts for wires.

3-6 Installing the AC Junction Box and PV Rack

Operation temperature

Maximum operation temperature: 65°C (149°F).
Minimum operation temperature: -40°C (-40°F).

Design strength

Refer to Appendix 2 – Module Installation & Load Guide

PV module specification (conditions of 1000W/m

2

irradiance and 25°C (77°F) solar cell temperature)

Notes
- LG AC module should not be operated in locations where direct contact to salt water or ammonia exists.

15

Copyright © 2017 LG Electronics.

All Rights Reserved.

All of procedures should be carried out by qualified installers. LG Electronics does not provide
warranty for PV racks and the AC junction box.

PV racks

AC Junction Box

«
...
13
14
15
16
17
...
»

Содержание LG A1C-A5 Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для LG A1C-A5 Series

Бренд: Srne Страницы: 38

Бренд: Daikin Страницы: 21

Бренд: Gbxpoint Страницы: 4

Бренд: My Cable Mart Страницы: 4

EnerSolis ES3000T

Бренд: Ablerex Страницы: 25

Mobitronic 8100-012VS

Бренд: Waeco Страницы: 7

Бренд: B&B Electronics Страницы: 2

Бренд: Agilent Technologies Страницы: 70

COMMAND VALVE P1012593

Бренд: Ideal Vacuum Страницы: 9

PROFINET Master HD67B70-232-A1

Бренд: ADF Web Страницы: 31

Бренд: World Friendship Страницы: 17

Бренд: Mitsubishi Страницы: 143

Бренд: C&C TECHNIC Страницы: 2

Бренд: Lika Страницы: 2

Бренд: Transition Networks Страницы: 7

Бренд: Emergi-Lite Страницы: 12

Бренд: Larco Страницы: 11

Бренд: red lion Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды