LG LG A1C-A5 Series Скачать руководство пользователя страница 22

Страница: 22 / 107

AC Module System Installation Manual

Rev. 1.0

•

Do not bend the cable too many times. It may result in mechanical and/or electrical problems.

•

Do not disconnect AC cable connectors under load.

•

Use the dedicated unlocking tool to remove the connector. Do not use any other tools.

•

The following unlocking tool is available for disconnecting the combined AC cable connectors.

•

The male and female connectors will be opened by fully depressing the unlocking tool into the latches.

•

After the unlocking tool insertion is complete, pull the connectors apart.

•

Avoid all external interference to the connector.

•

Do not impose force on the side direction of the connector.

•

Do not apply too much force on AC cables away from connectors or a micro inverter.

•

The cable must not be bent, crushed or pinched on the direct exit of the cable screw joint.

•

The cable must be routed in a way that the tensile stress on the conductor or connections is prevented.

•

A minimum bending radius R≥ 55mm (5 x Cable diameter) must be maintained.

•

Do not attempt to assemble connectors in wet, soiled, or dusty environment.

•

Keep connectors dry and clean, and ensure that connectors have no damage or deforms.

•

Avoid connectors resting on the ground or roof surface. AC cables should be kept way from the ground or roof
surface. Use proper tools like cable ties for securely attaching AC cables on structures like PV racks.

•

Avoid sunlight exposure and water immersion of the connectors.

•

Incomplete connections can result in arcs and electrical shock.

•

Check that all AC cables are securely fastened to structures.

•

Ensure that all locking connectors are fully engaged and locked.

•

Do not leave unconnected (unprotected) connectors exposed to the environment. Use appropriate end caps for the
unconnected AC cable connectors.

AC Cable Connector removal

Unlocking Too l

•

To prevent the danger of the electric shock, make sure to turn off the circuit breaker before the installation.

•

Do not disconnect AC cable connectors under load.

Содержание LG A1C-A5 Series











































































































Результаты поиска

Содержание LG A1C-A5 Series

Отзывы:

Похожие инструкции для LG A1C-A5 Series

Бренды по названию

Популярные бренды

LG LG A1C-A5 Series, Руководство по установке

Результаты поиска

Содержание LG A1C-A5 Series

Отзывы:

Похожие инструкции для LG A1C-A5 Series

Бренды по названию

Популярные бренды