LG LDF7774BB Скачать руководство пользователя страница 19

Страница: 19 / 68

For Authorized Service Technician

- 19 -

- 15 -

Fan Assembly

Inner Cover

Gasket

Flange

Hose

Detergent

Dispenser

Door Hinge

Air Duct

Door Bracket

3) Fan Assembly

Open the door.
Remove 4 screws and a earth screw for

Door Bracket.
Remove the wire connetions.
Remove the Air Duct.
Turn the Inner Cover counterclockwise.

4) Detergent Dispenser

Close the door

Remove the wire connections.
Remove 6 screws with brackets.
Push the Detergent slowly pulling up the
the Flange by Standard Screwdriver.

5) Door Spring (Right & Left)

Push the Spring upwards and take it off

from the the slot.

Be careful not to be injured by the

sharpedge of Tub.

Take off the Hinge Link from the Hinge.

6) Door Liner

Open the door.
Pull the Door Liner and take it off from

the Hinge Supporter.

Door Liner Assembly

Hinge Supporter

Содержание LDF7774BB





































































Результаты поиска

Содержание LDF7774BB

Отзывы:

Похожие инструкции для LDF7774BB

Бренды по названию

Популярные бренды

LG LDF7774BB, Руководство по обслуживанию

Результаты поиска

Содержание LDF7774BB

Отзывы:

Похожие инструкции для LDF7774BB

Бренды по названию

Популярные бренды