manualshive.com logo in svg

LG LDF7774BB, Руководство по обслуживанию

Поделиться
Скачать
LG LDF7774BB Скачать руководство пользователя страница 45

For Authorized Service Technician

For Authorized Service Technician

- 45 -

8. INSTALLATION INSTRUCTION

- 30 -

- 30 -

Figure A

Step 2: PREPARE THE ELECTRICAL WIRING

1. This appliance must be operated with correct voltage as shown in this manual and on the

rating plate, and connected to an individual, properly grounded branch circuit, protected

by time delay fuse. Wiring must be 3 wires including ground.

2. The wiring or cord should be in an accessible location adjacent to, and not behind the

dishwasher and within 4 ft. (1.2m) of the dishwasher side. 

3. The wiring or cord must be grounded properly, if in doubt, have it checked by a qualified

electrician. No other appliance shall be connected to the same outlet by a double adapter

or similar plug.

4. The wiring or cord must be oriented as shown in Figure A below.
5. Check the dishwasher for any damage before trying to install it.
6. Make sure water line and Electrical line are oriented in the bottom channels as shown in

the figure below.

If you find any damage to the dishwasher, Please contact your dealer or builder

immediately.

WARNING

For personal safety, remove house fuse or open circuit breaker before installation. 

Do not use an extension cord or adapter plug with this dishwasher.

Electrical and grounding connections must comply with the national electrical

code/provincial and municipal code and/or other local codes.

Содержание LDF7774BB





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды