3
Enter the Configuration ID 1.
•
Change the left character or digit first.
•
To change the value of a character or digit, press
Left
to decrease or
Right
to increase the underlined value, and
press
Select
to move to the next character or digit.
•
To move to the next character or digit without changing the current value, press
Select
.
•
When you press
Select
on the last digit, the value will be submitted.
If
Invalid ID
appears, then the entry is discarded, and the previous Configuration ID 1 is displayed on the
screen.
If the process is successful, then
Submitting Selection
appears on the display, followed by the current
value for Configuration ID 2.
4
Repeat the steps for entering the Configuration ID 2, and press
Select
.
If the Configuration ID 2 is validated,
Submitting Selection
appears, and a check mark appears next to
Printer Setup
.
5
Restart the printer. A POR is not automatically performed.
Transfer Module Barcode
The 16-digit numeric value matches the transfer module installed in the printer. If you replace the transfer module,
reenter this value.
Stop
exits the menu.
To enter the transfer module barcode:
1
Select
Printer Setup
from Diag Menu, and press
Select
.
2
Select
ITU Barcode
, and press
Select
.
3
To enter the 16-digit numeric value:
•
Use
Left
to decrease the left most digit value or
Right
to increase the value.
•
Press
Select
to advance to the next digit.
•
If a digit is already correct, then press
Select
to accept the number and to continue.
•
When the last number is entered and you press
Select
,
Submitting changes…
should appear.
•
If the entered number is incorrect, then
Check Sum Does Not Match
displays. Check and reenter the
number.
Reset Fuser Count
Resets the fuser count value to zero. The Event Log records each time that a user executes the Reset Fuser Count
operation. See
for more information. This setting appears only if the Maintenance Warning
and Intervention function is enabled in the printer Configuration ID.
To reset the fuser count:
1
Select
Printer Setup
from Diag Menu, and press
Select
.
2
Select
Reset Fuser Cnt
, and press
Select
.
3
Select
Reset
, and press
Select
.
Reset Resetting…
appears.
4
To cancel a reset, press
Back
.
7527
Service menus
207
Содержание XC2132
