Error code
Description
Action
903
Busy tone detected.
Check with remote end if successive
attempts fail.
904
Hardware error detected.
See
“Modem/fax card service check” on
905
A timeout occurred after dialing the number
and waiting for a response.
Check with remote end if successive
attempts fail.
906
Fax cancelled by user.
No action needed.
907
Modem detected a digital line connection.
Verify the MFP is connected to an analog line.
See
“Fax transmission service check” on
908
Phone line was disconnected
Restore phone line connection.
A00
Received request for unsupported function
from remote fax device.
No action needed.
A01
Received request for unsupported image width
from remote fax device.
No action needed.
A02
Received request for unsupported image
resolution from remote fax device.
No action needed.
A03
Received request for unsupported compression
type from remote fax device.
No action needed.
A04
Received request for unsupported image length
from remote fax device.
No action needed.
F00
Unknown error occurred.
No action needed.
Escalating a fax issue to second
‑
level support
Before contacting the second-level support, go to the SE menu on the MFP, and then generate a Fax error file. This file
contains machine settings information and debug information that will help second-level support determine the cause
of a failure.
To generate the fax error file, perform the following steps:
1
In a Web browser, type
http://MFP/<IP address>/se
.
2
The MFP’s SE menu page will display. Click the “Dump Job History” link. The following displays:
3
Write down the type of connection, the type of error, and the job in which the error occurred.
7527
Diagnostic information
160
Содержание XC2132
