Lexmark X500N Скачать руководство пользователя страница 78

Страница: 78 / 244

2-40

Service Manual

7100-XXX

Operator panel service check

USB service check

Network service check

Step

Questions / actions

Yes

Is the operator panel cable properly
connected to the op panel?

Go to step 2.

Properly connect the cable
to the op panel.

Is the op panel cable properly connected to
the RIP board connector J-PNL1?

Go to step 3.

Properly connect the cable
to J-PNL1.

Check the op panel cable continuity. Is there
continuity?

Go to step 4.

Replace the flatbed unit.
See

“Flatbed assembly

removal” on page 4-49

Check Voltages on J-PNL1, located on the
RIP card. Pin 1 voltage should measure 5V.
Is it correct?

Replace the operator panel.
See

“Operator panel

removal” on page 4-57

Replace the system board.
See

“System board

removal” on page 4-36

Step

Questions / actions

Yes

Is the USB cable properly connected to the
MFP and host PC?

Go to step 2.

Properly connect the cable
at both ends.

Try a different USB cable. Does this fix the
issue?

Issue fixed.

Go to step 3.

Connect a different device to the USB cable.
Did the host PC see the device?

Replace the RIP/system
board.See

“System board

removal” on page 4-36

There is an issue with the
host machine.

Step

Questions / actions

Yes

Ping the MFP using the address on the MFP
op panel. Is it responding?

Go to step 3

Go to step 2.

Is the ethernet cable properly connected to
the network card RJ-45 connector?

Go to step 3.

Properly connect the cable
to the RJ-45 jack.

Check to see if DHCP is being used on the
network. Is DHCP used?

Go to step 4.

Go to step 5.

Does the MFP IP address match the ports
IP address on the driver?

Go to step 5.

Have the network admin
create a port on the host PC
matching the IP address on
the MFP. Assign the new
port to the driver.

Have the network admin try a new network
cable to the MFP. Did this fix the problem?

Problem resolved.

Replace the system board.
See

“System board

removal” on page 4-36

Содержание X500N





















































































































































































































































Результаты поиска

Содержание X500N

Отзывы:

Похожие инструкции для X500N

Бренды по названию

Популярные бренды

Lexmark X500N, Руководство по обслуживанию

Результаты поиска

Содержание X500N

Отзывы:

Похожие инструкции для X500N

Бренды по названию

Популярные бренды