Lexmark X500N Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 244

background image

General information

1-15

7100-XXX

Maintenance approach

The diagnostic information in this manual leads you to the correct field replaceable unit (FRU) or part.
Use the error code charts, symptom index, and service checks to determine the symptom and repair
the failure. The removals in the repair information chapter may help you identify parts.

•

Printer messages

•

Symptom tables

•

Service checks

•

Repair information

After you complete the repair, perform tests as needed to verify the repair. See “Diagnostic aids” on
page 3-1.

Standard inspection and cleaning procedure

•

Switch off printer power, and disconnect the AC power cord from the electrical outlet.

•

Remove and inspect the photodevelopers and toner cartridges, shielding them from strong light.

•

Inspect the interior of the printer, removing foreign matter such as paper clips, staples, pieces of paper
or transparencies, paper dust, hair, oil, grease, or toner.

•

Clean the printer interior using a lint-free cloth. Do not use solvents or chemical cleaners to clean the
printer interior.

•

Use only the specified oil or lubricant on printer parts (some service parts are lubricated at the factory).

•

Inspect and, if necessary, clean all rubber/plastic rolls with a lint-free cloth. Dry the rolls with a lint-free
cloth.

•

While cleaning, inspect the interior of the printer for damaged wires, loose connections, toner leakage,
loose springs, and damaged or worn parts.

•

Be sure the printer is on a single, flat, strong table or desk top.

•

Inspect all supplies (OCR, cartridges, photodevelopers/toner cartridges, belts, fuser maintenance kits
and paper sources (cassettes, trays, feeders, duplex drawers, finisher, mailbox trays) for obvious
damage and proper installation (paper guides not too tight). Inspect for correct media usage (paper,
transparencies, labels).

•

Print demo page.

•

If additional paper sources are installed, print a demo page from each of these (if possible).

•

Failure to print from an additional tray or feeder may imply one or more pins are bent in the mating
connector.

«
...
33
34
35
36
37
...
»

Содержание X500N





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X500N

Power Defense PD3

Бренд: Eaton Страницы: 4

Бренд: Xerox Страницы: 262

Бренд: Kyocera Страницы: 157

3500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 6

Бренд: Lexmark Страницы: 13

8560MFPD - Phaser Multifunction Printer Color Laser

Бренд: Xerox Страницы: 20

THERMOMARK ROLLMASTER 300

Бренд: Phoenix Contact Страницы: 42

Бренд: Avery Dennison Страницы: 68

Бренд: FujiFilm Страницы: 28

Бренд: Triumph Adler Страницы: 202

Бренд: Oki Страницы: 239

Pixma G2030 Series

Бренд: Canon Страницы: 351

PIXMA G2070 Series

Бренд: Canon Страницы: 358

Бренд: Canon Страницы: 430

Бренд: Canon Страницы: 430

Бренд: Canon Страницы: 271

Бренд: Epson Страницы: 16

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды