Lexmark Pro910 Series Скачать руководство пользователя страница 25

Страница: 25 / 118

Diagnostic information

2-5

Lexmark Pro910 Series

Go Back

Ink cartridge error messages

Error

Control panel message

Action

Cartridge missing

Printhead Damage May Occur!

and

Faxes in Memory

Reinsert the [x] Cartridge

Reinsert the following
Cartridges:

Technical Support Center:

Open the printer cover, and check the
ink cartridges for proper installation. If
properly installed, then replace the ink
cartridges.

Service:

Inspect the tank contact card:

• Wipe it using a clean, lint-free

cloth.

• If the contacts show signs of

damage, replace the tank contact
card. See

“Tank contact card

removal” on page 4-18

Cartridge not supported

Cartridge Unsupported

and

Faxes in Memory

[x] Cartridge Unsupported

The following Cartridges are
unsupported:

Unable to authenticate cartridge

Cartridge Error

and

Faxes in Memory

Unable to Authenticate [x]
Ink Cartridge

The following Cartridges
cannot be authenticated:

Содержание Pro910 Series























































































































Результаты поиска

Содержание Pro910 Series

Отзывы:

Похожие инструкции для Pro910 Series

Бренды по названию

Популярные бренды

Lexmark Pro910 Series, Руководство по обслуживанию

Результаты поиска

Содержание Pro910 Series

Отзывы:

Похожие инструкции для Pro910 Series

Бренды по названию

Популярные бренды