manualshive.com logo in svg

Lexmark 5060-00x, Руководство по обслуживанию, Страница: 42 / 490

Поделиться
Скачать
Lexmark 5060-00x Скачать руководство пользователя страница 42

2-8

Service Manual

5060-00

x

 

960 RAM Memory Error

RAM soldered on board is bad. Replace the RIP board. See 

“RIP board 

removal” on page 4-70

.

961 RAM Memory Error

Errors 961 through 963 indicate that a memory error has occurred on 
RAM 

x

 in slot 

x

 installed on the RIP card. If available, switch memory 

from the failing slot with one from a non-failing slot to see if this fixes the 
problem. If it does not fix the problem, replace the RIP board. If another 
RAM option is not available, replace the RAM that is failing. If this does 
not fix the problem, replace the RIP board. See 

“RIP board removal” on 

page 4-70

.

962 RAM Memory Error

963 RAM Memory Error

964 Emulation Error

Download Emulation CRC failure has occurred.

The following actions may be taken:

1. Disable Download Emulation.
2. Program the download emulation into the code overlay SIMM, again.
3. If the problem is not resolved, replace the code overlay SIMM and 

download emulation, again.

975 Standard Network
or
Network Card 

x

Unrecognizable network errors 975 through 979 indicate a failure with 
the standard network port located on the RIP board or a network card in 
the specified slot 

x

, 

x

=1, 2 or 3. If unable to clear the error message, 

check the following:

• If installed, check network card for correct installation.
• If correctly installed, replace the network card.
• If a network card is not installed, replace the RIP board.

976 Standard Network

Unrecoverable software or error in network port. Network card 

x

. If 

unable to clear the error message, check the following:

• If installed, check network card for correct installation.
• If correctly installed, replace the network card.
• If a network card is not installed, replace the RIP board.

978 Standard Network
or
Network Card 

x

 

Bad checksum while programming network card 

x

 port.

979 Standard Network
or
Network Card X

Flash parts failed while programming network card 

x

 port.

980 <

device

> comm

Engine is experiencing unreliable communications to the specified 
device.

981 <

device

> comm

Engine protocol violation detected by the specified device.

• Engine
• Duplex option
• Tray 

x

 (where 

x

=1,2,3,4, or 5)

• Output bin (where 

x

=1,2,3, or 6)

Note: 

This message is used for single bin output devices.

• Bin 

x

 to y (where 

x

 to y=1 to 5).

Note: 

This message is used for multiple bin output devices.

982 <

device

> comm

Communications error detected by the specified device.

• Engine
• Duplex option
• Tray 

x

 (where 

x

=1,2,3,4, or 5)

• Output bin (where 

x

=1,2,3, or 6)

Note: 

This message is used for single bin output devices.

• Bin 

x

 to y (where 

x

 to y=1 to 5).

Note: 

This message is used for multiple bin output devices.

Error code

Action

Содержание 5060-00x











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов