manualshive.com logo in svg

Lexmark 5060-00x, Руководство по обслуживанию, Страница: 292 / 490

Поделиться
Скачать
Lexmark 5060-00x Скачать руководство пользователя страница 292

4-74

Service Manual

5060-00

x

 

13.

Disconnect the three sensors (A) from the frame. 

Service tip:

 A light aimed toward the grounding clip (B) makes the removal easier.

Service tip: 

Leave the old sensor cable assembly (C) in place temporarily after disconnecting the sensors 

as a guide to placement of the sensors for the new assembly. Lay the new sensor cable assembly beside 
the old one and connect the new sensors as you remove the old assembly. The new sensor cable 
assembly is installed on the other side of the grounding clip (closer to the fuser), so you do not have to 
reinstall the new sensor cable assembly between the clip and upper frame channel.

14.

Pull the old sensor cable assembly to remove it.
Observe the routing of the cable, especially the location of the cable (C) around the grounding clip (B). The 
new cable will be installed on the opposite side of the clip.
Pulling too firmly on the sensor cable assembly may unseat the grounding clip. The old cable assembly 
runs between the frame and the grounding clip.

A

B

C

Содержание 5060-00x











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов