Lexmark 5060-00x Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 490

Lexmark 5060-00x Скачать руководство пользователя страница 118

2-84

Service Manual

5060-00

x

271 Paper jam - Check Bin 1

Output expander—POST incomplete.

Output Expander, POST complete—First sheet of paper feeds into Output Bin

1

.

Note:

Before proceeding with this service check run the Output Bin

x

Sensor Test and check for the failing

sensor.

Sensor tests:

Step

Actions and questions

Yes

No

1

Pass thru sensor flag—check the sensor flag for
correct operation.

Is the flag operating correctly?

Go to step 2

Repair or replace
as necessary

2

Pass thru sensor cable—make sure the pass thru
sensor cable is correctly connected to J

3

on the control

board.

Is the cable connected correctly?

Go to step 3

Reseat the cable

3

Voltage check—disconnect the pass thru sensor cable
from the control board and check the voltage on J3-3.
The voltage measures approxi5 V dc.

Is the voltage correct?

Go to step 4

Replace the control
board

4

Voltage check—measure the voltage at J3-2. The
voltage measures approximately 0 V dc.

Is the voltage correct?

Replace the control
board

Replace the sensor
assembly

XNF

Near Full (Upper part of sensor assembly)

F

Full (Lower part of sensor assembly)

P

Pass Thru Sensor

Step

Actions and questions

Yes

No

1

DC motor cable connection—make sure the DC motor
connector is correctly installed at J4 on the Output
Expander Option board.

Is the cable installed correctly?

Go to step 2

Install the cable
correctly.

2

DC motor mechanical linkage assembly—check the
resistance of the motor on the cable connector. Check
the resistance between J4-1 and J4-2. The resistance
measures between 115 and 135 ohms.

Is the resistance correct?

Go to step 3

Replace the DC
motor mechanical
linkage assembly.

3

D.C. motor mechanical linkage assembly—check for
continuity between J4-1 and J4-2 and the case of the
motor. It measures infinity.

Is there continuity between J4-1 or J4-2 and the case
of the motor?

Note

: If the motor is shorted from either J4-1 or J4-2

and the case of the motor, it may be necessary to
replace the output expander control board.

Replace the DC
motor mechanical
linkage assembly.

Go to step 4

«
...
116
117
118
119
120
...
»

Содержание 5060-00x











































































































































































































































































































































































































































































































Отзывы:

Нет отзывов