Leviton NorthStar Site Controller Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 65

background image

4 CONFIGURATION

23

4.2

Set and Encrypt the SNAP Communications Channel

Leviton recommends you enable encryption within your NorthStar installation.
Encryption is enabled by clicking the

Encryption

toggle to shift it to

Enable

. This

will encrypt all data transmitted over the air and signiﬁcantly reduce the possibility of
outside interference.

Particularly large lighting installations can generate a lot of network trafﬁc, and in
some rare occasions this can have a negative impact on system response times.
If you encounter a situation where lights aren't responding to commands, enabling

Enhanced CRC

may help. It is enabled via the

Enhanced CRC

toggle switch

NOTE:

By default, encryption and enhanced crc are disabled.

NOTE:

If any conﬁgured light within your installation is not in communications with the

site controller the system will not change channels or encrypt. This is to ensure that
all lights are reconﬁgured, or none of them. If you've entered a "fake light" or sensor,
you'll need to delete it before initiating a change.

NorthStar uses a SNAP RF network for lighting control, and proper precautions
will help ensure reliable service. For maximum reliability and security, Leviton
recommends you change and encrypt the default SNAP channel and network ID.

To change the SNAP channel:

1. Log-in to the NorthStar user interface and click

Conﬁg - Network Settings

.

2.

Enter a new SNAP channel in the provided

Channel

ﬁeld. Valid channels range

from 1-13.

NOTE:

For NorthStar installations near a strong Wi-Fi installation, Leviton

recommends that you use SNAP channel 4 or 9 to minimize interference on the
lighting network.

3.

Enter a new Network ID in the

Network ID

ﬁeld. Network IDs is any combination

of numbers and the letters a - f. (Excluding 0000 and ffff.)

4.

Click

the

Enable

toggle under

Encryption

.

5.

Click

the

Enable

toggle under

Enhanced

CRC.

6.

Click

the

Save Changes

button to save your changes and exit.

When the Save Changes button is clicked, all components in your installation will be
updated to the new information over the next several minutes

NOTE:

The factory default channel (1) and Net ID (d110) should not be used for

installations. Valid channels range from 1 - 13, and Network IDs is any 4 digit
combination of numbers and the letters a - f. (Excluding 0000 and ffff.)

WEB

VERSION

«
...
22
23
24
25
26
...
»

Содержание NorthStar Site Controller


































































Отзывы:

Нет отзывов

Похожие инструкции для NorthStar Site Controller

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: Gascat Страницы: 32

Бренд: National Instruments Страницы: 8

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

Бренд: TCi Страницы: 9

Бренд: POLA Страницы: 2

Бренд: WAGNER Страницы: 128

Бренд: Hiwin Страницы: 99

Бренд: Baier Страницы: 20

Бренд: IDTECK Страницы: 51

Бренд: BG Systems Страницы: 24

ESC Classic 50A

Бренд: LETON Страницы: 2

Бренд: Danfoss Страницы: 13

Бренд: ETI Страницы: 14

Бренд: meitav-tec Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды