Leviton NorthStar Site Controller Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 65

background image

2.4

The NorthStar Site Controller

The site controller serves as the heart of your lighting solution, allowing local control with
or without the internet. The site controller can work alone or with other site controllers to
unify the lighting controllers into a NorthStar lighting solution.

2 INSTALLATION AND INITIAL SETUP

10

2.4.1 Buttons on the NorthStar Site Controller

There are three buttons on the site controller. The button closest to the antennas,

button one, clears the NorthStar database. Button two resets the username and
password to the default settings, and the third button is inactive and not used.
(Buttons must be held down until the front panel LEDs change color before a reset
will take effect. More information on using the site controller buttons is provided in
Administration on page 56).

2.4.2 Setting up the NorthStar Site Controllerv

The ﬁrst step in installing a NorthStar lighting solution is to physically install the light

ﬁxtures, lighting controllers and sensors, which can then be conﬁgured by accessing
the user interface of the NorthStar site controller. These instructions assume that
you have already installed the lights and lighting controllers that will make up your
NorthStar lighting solution and you are now ready to set up the site controller.

To install the NorthStar site controller:

1. Unpack the

NorthStar Site Controller

.

2. Attach the included antennas to

the site controller as shown. When
looking at the top of the site controller
(with the mounting bracket on the
back side), the longest antenna
(SNAP antenna) attaches to the
left- most antenna connector, and
the shorter Wi-Fi antenna attaches
to the middle connector. If the site
controller that you're installing has
cellular capability, the optional cell
antenna is attached to the remaining
connector. Leviton-provided antennas
will have white dots at the base of
the antenna that denote the type.
One dot is a SNAP antenna, two
is for a Wi-Fi antenna, and three
is for a cellular antenna. This
notation is also reﬂected on the front
unit label of the site controller.

3. Plug the provided power supply into the barrel connector and then into an 110VAC

outlet. When the

NorthStar Site Controller

powers up, orange LEDs will light up for

approximately 30 seconds while the site controller software starts up. Once this is
complete, the orange LEDs will turn off and the site controller will be ready to use.

OR

4. Install the NorthStar site controller in the OC00G-ENC enclosure, using the

integrated power supply and antennas provided in the enclosure

SNAP Antenna

Wi-Fi Antenna

Button 1

Button 2

Button 3

Ethernet Port

Input Voltage

micro-B USB Port

Cellular Antenna

(Optional)

USB Standard-A

Receptacle

WEB

VERSION

«
...
9
10
11
12
13
...
»

Содержание NorthStar Site Controller


































































Отзывы:

Нет отзывов

Похожие инструкции для NorthStar Site Controller

Бренд: Manfrotto Страницы: 16

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: tams elektronik Страницы: 60

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Zeta Страницы: 44

Бренд: Ziton Страницы: 36

Бренд: Savant Страницы: 2

Бренд: Sven Страницы: 6

Бренд: Carel Страницы: 48

Бренд: ESBE Страницы: 4

Controller CR100

Бренд: Sonos Страницы: 12

Бренд: Adaptec Страницы: 2

Бренд: Webasto Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды