LevelOne FPS-2013TXU Скачать руководство пользователя страница 9

Страница: 9 / 88

LAN Installation

This chapter describes how to install the LevelOne Printer Server in
your Local Area Network.

Procedure

1. Find the Default LevelOne Printer Server Name

•

The

Default Server Name

is shown on a sticker on the base of the device. It

consists of 8 letters and/or digits.

•

Record this name, it will be needed during configuration.

During configuration you will be able to change the
device name. The new name MUST NOT contain any
spaces or blanks

2. Connect the Printer(s)

•

Connect the printer or plotter to the LevelOne Printer Server's printer port(s), as

appropriate:

•

Use standard Parallel port cables to connect the printer to the parallel port on the

LevelOne Printer Server. Parallel printer cables should be less than 3 meters long.

Leave the LevelOne Printer Server powered OFF
while connecting it to the Printer(s) and the LAN.

3. Connect the Network Cable

•

Connect the LevelOne Printer Server to your LAN. For 10/100BaseT interfaces,

the LevelOne Printer Server will automatically detect the correct speed.

- 6 -

Содержание FPS-2013TXU

























































































Результаты поиска

Содержание FPS-2013TXU

Отзывы:

Похожие инструкции для FPS-2013TXU

Бренды по названию

Популярные бренды

LevelOne FPS-2013TXU, Руководство пользователя

Результаты поиска

Содержание FPS-2013TXU

Отзывы:

Похожие инструкции для FPS-2013TXU

Бренды по названию

Популярные бренды