LevelOne FPS-2013TXU Скачать руководство пользователя страница 65

Страница: 65 / 88

Level One Printer Servers

Internet Printer Server

•

TCIP/IP Protocol.

The LAN must use the TCP/IP protocol.

•

Mail Server Access.

The LevelOne Printer Server must be able to access the Mail

Server using a single IP address.

•

Mail Account.

The LevelOne Printer Server must have a Mail Account. Users print by

sending an E Mail to this mail account.

User (Client) Requirements

•

Internet Connection.

Either through a LAN, or dial-up.

•

E Mail address.

This is used to notify the user that their print job has been done, or if

there any problems.

•

Printer Driver.

Users must have a printer driver which matches the printer connected

to the remote Internet Printer Server.

•

Print Capture Software.

To print more than plain text, users require InterNet Printing

Port software to capture the print job and convert it into an E Mail attachment.
The InterNet Printing Port software is available for the following operating systems:

•

Microsoft Windows 95/98

•

Microsoft Windows NT 3.51 or later.

- 62 -

Содержание FPS-2013TXU

























































































Результаты поиска

Содержание FPS-2013TXU

Отзывы:

Похожие инструкции для FPS-2013TXU

Бренды по названию

Популярные бренды

LevelOne FPS-2013TXU, Руководство пользователя

Результаты поиска

Содержание FPS-2013TXU

Отзывы:

Похожие инструкции для FPS-2013TXU

Бренды по названию

Популярные бренды