Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 85 / 100

EDS84DMOTPBUS EN 3.0 - 11/2011

Communication manual 8400 motec PROFIBUS

Parameter reference

Parameters relevant for PROFIBUS communication

C13866

C13867

C13880

C13881

Parameter | Name:

C13866 | Display: Most recent CFG data

Data type: OCTET_STRING

Index: 10709

= 29D5

Display of the last configuration data sent by the PROFIBUS master with the "Chk-Cfg" telegram (ASCII string with

22 characters)

;

Read access

Write access

CINH

PLC-STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13867 | Display: Most recent diagnostic data

Data type: OCTET_STRING

Index: 10708

= 29D4

Display of the last diagnostic data sent to the PROFIBUS master (ASCII string with 16 characters)

;

Read access

Write access

CINH

PLC-STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13880 | Reaction on communication failure

Data type: UNSIGNED_8

Index: 10695

= 29C7

Monitoring response to a communication fault on the PROFIBUS

• A change in the monitoring response is effective immediately.

Permanent interruption of PROFIBUS communication (



69)

Selection list

0 No response
1 Error
4 Warning locked

Subcodes

Lenze setting

Info

C13880/1

0: No response

The response set here for the "watchdog/data exchange"

monitoring is executed if the bus station ...

• does not receive a message from the master within

the watchdog monitoring time (during an active

connection displayed under

C13882/1

• detects that it is no longer in the "Data_Exchange"

state. Please see also the notes given under

C13881

;

Read access

;

Write acces

CINH

PLC-STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13881 | Monitoring time: Data exchange

Data type: UNSIGNED_16

Index: 10694

= 29C6

If the "Data_Exchange" state has been exited, the response parameterised with

C13880/1

is carried out when the

monitoring time set here for the data exchange has expired.

• A value of "65535" in this code deactivates the monitoring function.

• A change in monitoring is effective immediately.

• The value set here for the monitoring time must be smaller than the watchdog monitoring time (displayed under

C13882/1

Permanent interruption of PROFIBUS communication (



69)

Setting range

(min. value | unit | max. value)

Lenze setting

65535

65535 ms

;

Read access

;

Write acces

CINH

PLC-STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды