Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 53 / 100

EDS84DMOTPBUS EN 3.0 - 11/2011

Communication manual 8400 motec PROFIBUS

Parameter data transfer

PROFIdrive parameter data channel (DP-V1)

9.3.2

Acyclic data transfer

[9-3]

Transmission directions

Explanation



A "Write.req" is used to pass the data set (DB47) to the slave in the form of a parameter

request.



With "Write.res" the master receives the confirmation for the receipt of the message.



The master requests the response of the slave with "Read.req".



The slave responds with "Read.res (-)" if processing has not yet been completed.



After parameter processing, the parameter request is completed by transmitting the

parameter response to the master with "Read.res (+)".



Note!

A parameter request refers to one or several parameter(s) (multi-parameter

request).

E94YCPM011

Master

Slave

DP-V1

Write.res

Write.req

with data (parameter request)

with data (parameter response)

without data

Read.req

Read.res (-)

Read.req

Read.res (+)

Parameter response

Parameter request

Parameter
processing

Parameter response

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды