Lenze E84DGFCp Series Скачать руководство пользователя

Страница: 74 / 100

Communication manual 8400 motec PROFIBUS

Diagnostics

Querying the current bus status

EDS84DMOTPBUS EN 3.0 - 11/2011

11.3

Querying the current bus status

Code

C13861

displays the current PROFIBUS status is a bit-coded form:

Bit assignment

Description

Bit 3

Bit 2

Bit 1

Bit 0

Reserved

Bit 5

Bit 4

State of the DP state machine (DP-STATE)

WAIT_PRM

The slave waits for a parameter data telegram after

acceleration. Other types of telegrams will not be processed.

Data exchange is not yet possible.

WAIT_CFG

The slave waits for the configuration telegram that specifies

the number of input and output bytes. The master informs

the slave about the number of I/O bytes that will be

transferred.

DATA_EX

If the parameter settings and the configuration have been

accepted by the firmware and by the application, the slave

state changes to "Data_Exchange" (exchange of user data

with the master).

Not possible

Bit 7

Bit 6

State of the Watchdog-State-Machine (WD-STATE)

BAUD_SEARCH

The slave is able to recognise the baud rate automatically.

BAUD_CONTROL

After recognising the correct baud rate, the slave status

changes to BAUD_CONTROL, and the baud rate is monitored.

DP_CONTROL

The DP_CONTROL status serves for response monitoring of

the master.

Not possible

Bit 11 Bit 10 Bit 9

Bit 8

Detected PROFIBUS baud rate

12 Mbps

6 Mbps

3 Mbps

1.5 Mbps

500 kbps

187.5 kbps

93.75 kbps

45.45 kbps

19.2 kbps

9.6 kbps

Bit 15 Bit 14 Bit 13 Bit 12

Reserved

Содержание E84DGFCp Series





































































































Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды

Lenze E84DGFCp Series, Руководство по связи

Результаты поиска

Содержание E84DGFCp Series

Отзывы:

Похожие инструкции для E84DGFCp Series

Бренды по названию

Популярные бренды