manualshive.com logo in svg

Lenze AC Tech PositionServo 940, Руководство пользователя

Поделиться
Скачать
Lenze AC Tech PositionServo 940 Скачать руководство пользователя страница 42

S94P01C -e1

40

6.3.1.3  Position Mode

In this mode the drive reference is a pulse-train applied to P3.1-4 terminals, if the 
parameter “Reference” is set to “External”. Otherwise the reference is taken from 
the drive’s internal variable. (Refer to the PositionServo Programming Manual for 
details). 

P3.1-4 inputs can be configured for two types of signals: step and direction and 
Master encoder quadrature signal. Refer to section 5.2.1 for details on these 
inputs connections. Refer to section 8.3 for details about positioning and gearing.

When the Reference is set to Internal, the drives reference position, (theoretical 
or Target position), is generated by trajectory generator. Access to the trajectory 
generator is provided by motion statements, MOVEx and MDV, from the User 
Program. (Refer to the PositionServo Programming Manual for details).

6.3.2  Drive PWM frequency

This parameter sets the PWM carrier frequency. Frequency can be changed only 
when the drive is disabled. Maximum overload current is 300% of the drive rated 
current when the carrier is set to 8kHz. It is limited to 250% at 16kHz.

6.3.3  Current Limit

The CURRENT LIMIT setting determines the nominal currents, in amps RMS per 
phase, which output to the motor phases. To prevent the motor from overloading, 
this parameter is usually set equal to the motor nominal (or rated) phase current. If 
MotionView (6.04) or higher is used, the Current Limit is set equal to the nominal motor 
phase current by default when a motor model is selected. To modify this parameter, 
refer to section 6.3.23.

6.3.4  8 kHz Peak Current Limit and 16 kHz Peak Current Limit

Peak Current Limit sets the motor RMS phase current that is allowed for up to 2 
seconds. After this two second limit, the drive output current to motor will be reduced 
to the value set by the Current Limit parameter. When the motor current drops below 
nominal current for two seconds, the drive will automatically re-enable the peak 
current level. This technique allows for high peak torque on demanding fast moves 
and fast start/stop operations with high regulation bandwidth. If 8 kHz is used for Drive 
PWM frequency, use the parameter 8 kHz Peak Current Limit, otherwise, use 16 kHz 
Peak Current Limit.

If MotionView (6.04) or higher is used, the Peak Current Limit is set equal to 2.5 
times the nominal motor phase current by default when a motor model is selected. To 
prevent motor from overloading, the Peak Current Limit shall be set no higher than the 
maximum motor current. Otherwise, the motor may be damaged due to overheating. 
To modify this parameter, refer to section 6.3.23. 

6.3.5  Analog Input Scale (current scale)

This parameter sets the analog input sensitivity for current reference used when the 
drive operates in torque mode. Units for this parameter are A/Volt. To calculate this 
value use the following formula:

Iscale = Imax / Vin max 

 

Imax  

maximum desired output current (motor phase current RMS)

 

Vin max    max voltage fed to analog input at Imax

 

Example:

 

Imax  

= 5A (phase RMS)

 

 

Vin max  = 10V

 

 

Iscale 

= Imax / Vin max

 

 

 

= 5A / 10V = 0.5 A / Volt  (value to enter) 

Содержание AC Tech PositionServo 940












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды