Lenze AC Tech ESVZAP0 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

background image

15

CMVPFB01A

Cyclic Data Access

5.3 Channel Data Size

P415 and P416 - Data Sizes

Default: N/A

Range: 00.00 - 99.99

Access: RO

Type: Integer

During network setup, it is necessary to program the network master with the amount of IN and OUT
cyclic data used for each slave device that it is associated with. This process is simplified with the use
of GSD support files (refer to paragraph 4.2.2,

PROFIBUS-DP Master Setup Procedure,

for details).

The amount of cyclic data configured in each SMV PROFIBUS-DP module must be equal to the amount
configured in the network master. Failure to do this may result in lost data and/or network master
configuration errors.

To aid this routine the SMV PROFIBUS-DP module has two useful parameters that display the amount
of IN and OUT cyclic data configured in the master and drive. Refer to Table 9.

Table 9: Directional Data Sizes

Parameter

Function

Format

Description

P415

Master.Slave

Dout Data Size

xx.yy

xx = Master configured number of data WORDs

yy = Slave configured number of data WORDs

P416

Master.Slave

Din Data Size

xx.yy

EXAMPLE

The master PLC is configured for the slave node to have 4 IN words and 6 OUT words.

The drive is configured for 2 IN words and 6 OUT words

When the module is re-initialised (P418) as part of the commissioning routine it will fail to go online.
P419 will display the actual status.

Check P415 and P416 to identify the data size miss-match, i.e.
P415 = 04.02
P416 = 06.06

To clear the error, the amount of cyclic data used must be rectified and the module re-initialised
again.

NOTE

Depending upon the Acyclic data mode selected in P431 it may contribute towards the total
cyclic data count too. Refer to P431 for further details. The Acyclic data channels actually
utilise cyclic channels. Refer to section 6 for details on Acyclic parameter access

•

•

•

•

•

•

•

•

«
...
19
20
21
22
23
...
»

Содержание ESVZAP0


















































Отзывы:

Нет отзывов

Похожие инструкции для ESVZAP0

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: tams elektronik Страницы: 12

Бренд: National Instruments Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды