Lenze AC Tech ESVZAP0 Скачать руководство пользователя страница 40

Страница: 40 / 49

CMVPFB01A

Advanced Features

7.1.4 Module Time-out Action

P404 - Module Time-out Action

Default: 3

Range: 0 - 3

Access: RW

Type: Integer

This parameter controls the action to be taken in the event of a Module-to-Drive time out. The Time-out
period is fixed at 200 ms.

Table 32: Module Time-out Action

P404 Value

Description

No Action

Stop (controlled by P111)

Quick Stop

Fault

ntf

7.1.5 Module Firmware

P494 - Module Firmware

Default: N/A

Range: 1.00 - 99.99

Access: RO

Type: Integer

Displays the module firmware revision in the format of xx.yy, where: xx = Major version and yy = Minor
version

7.1.6 Module Internal Code

P495 - Module Internal Code

Default: 209-yy

Range:

Access: RO

Type: Integer

Displays the internal code revision in the format of xxx-yy. The display alternates between xxx- and -yy.

7.1.7 Missed Messages

P498 and P499 - Missed Messages

Default: N/A

Range:

Access: RO

Type: Integer

Table 33: Missed Messages

Parameter

Function

Description

P498

Missed Messages

Drive to Module

Displays the quantity of missed data messages being
transmitted from the drive to the option module

P499

Missed Messages

Module to Drive

Displays the quantity of missed data messages being
transmitted from the option module to the drive

Содержание ESVZAP0


















































Результаты поиска

Содержание ESVZAP0

Отзывы:

Похожие инструкции для ESVZAP0

Бренды по названию

Популярные бренды

Lenze AC Tech ESVZAP0, Справочник по интерфейсу связи

Результаты поиска

Содержание ESVZAP0

Отзывы:

Похожие инструкции для ESVZAP0

Бренды по названию

Популярные бренды