Lenze AC Tech ESVZAP0 Скачать руководство пользователя страница 46

Страница: 46 / 49

CMVPFB01A

Diagnostics

8.1 Faults

In addition to the normal drive fault codes, the additional codes listed in Table 39 may be generated by the
option module during a fault condition.

Table 39: Fault Codes

Fault Code

Definition

Remedy

F.ntF

Module Time-out

Module to drive communications time out.

Check cable and connection between drive and

option module.

F.nF1

Master Monitoring Time-out

Check network connection, cabling and termination.

Refer to section 7.3

Master Monitor

for details

F.nF2

Data Exchange Time-out

Check network connection, cabling and termination.

Refer to section 7.4

Data Exchange

for details

8.2 Troubleshooting

Table 40: Troubleshooting

Symptom

Possible Cause

Remedy

No communications

from the option

module

Module is not initialised

Check the drive to module connection.
Check P400 and P402.

•
•

Incorrect PROFIBUS-DP settings

Check P410 and P411.
If unsure of setting, reset PROFIBUS-DP parameters
to factory default using P403.

•
•

Improper wiring

Check wiring between the PROFIBUS-DP network
and communication module.
Ensure that the terminal block is properly seated.
Check connection between module and drive.

•

•
•

PROFIBUS-DP write

commands are

ignore or return

exceptions

"Network enabled" terminal is

either open or not configured

Configure one of the input terminals (P121, P122 or P123)

to "Network Enabled" function (selection 9) and close the

corresponding contact.

Drive stops for no

obvious reason

One of the PROFIBUS-DP

monitoring messages timed out

and its time-out reaction is set

to STOP.

Identify the time-out message (P423...P429) and modify

appropriate time-out time or reaction to the time-out

settings.

Module does not

enter the Data

Exchange State.

P419 displays 2 or 3

Data size configuration mismatch

between the Master and the Drive

Check the configuration sizes for Dout and Din Data.

Refer to Parameters P415 and P416.

Drive does not

change direction to

REVERSE

Parameter P112 is set to 0

(Forward Only)

Set drive parameter P112 to 1 to enable Forward &

Reverse direction

Содержание ESVZAP0


















































Результаты поиска

Содержание ESVZAP0

Отзывы:

Похожие инструкции для ESVZAP0

Бренды по названию

Популярные бренды

Lenze AC Tech ESVZAP0, Справочник по интерфейсу связи

Результаты поиска

Содержание ESVZAP0

Отзывы:

Похожие инструкции для ESVZAP0

Бренды по названию

Популярные бренды