Lenze AC Tech ESVZAP0 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 49

background image

CMVPFB01A

10

Commissioning

NOTE: Although there are only 4 modules listed in the GSD file, these can be used several times to create
the required amount of data.

Default Module: 2 IN 2 OUT
1 Word OUT Module
1 Word IN Module
4 Word Parameter Access Module

Find:

Profile:

-

Standard

SMVector

PROFIBUS(1): DP master

(5) SMVector

SMVector

SMVector

Figure 9: PROFIBUS-DP Master Setup

Save the configuration and download to the master.

4.3 Configuring the SMV PROFIBUS-DP Module

4.3.1 Connecting

With the drive power disconnected install the PROFIBUS-DP module and connect the network cable as
instructed in the preceeding sections. Ensure the drive Run / Enable terminal is disabled then apply the
correct voltage to the drive (refer to the drive's user manual for voltage supply details).

4.3.2 Setting the Network Protocol

P400 - Network Protocol

Default: 0

Range: 0 or 6

Access: RW

Type: Integer

Set P400 = 6 (PROFIBUS-DP)

Some SMV option modules are capable of supporting multiple protocols; therefore it is necessary to set the
required protocol. The option module is only initialised after a protocol has been selected.

4.3.3 Node Address

P410 - Node Address

Default: 126

Range: 0 - 126

Access: RW

Type: Integer

Set P410 to the required value. The default address is 126. The permissable address range is: 0 - 125

Each node on the network must have an individual address, if two of more nodes have duplicate addresses
this may prevent the network from functioning correctly. Node 126 is a special node address intended for
“New” nodes only where by node configuration is performed via a network master device.

7.

«
...
14
15
16
17
18
...
»

Содержание ESVZAP0


















































Отзывы:

Нет отзывов

Похожие инструкции для ESVZAP0

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Walimex Pro Страницы: 68

Бренд: Parker Страницы: 28

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: Vega Страницы: 20

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

Бренд: Full Gauge Controls Страницы: 3

Бренд: Dakota Digital Страницы: 12

Бренд: SOMFY Страницы: 112

Бренд: LCT Страницы: 5

Бренд: Yoshitake Страницы: 18

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды